Brother MFC-9320CW - User Manual

Other manuals for Brother MFC-9320CW

Service Manual578 pages

Quick Setup Guide49 pages

Network User's Guide203 pages

Questions and Answers:

G
Grace WilsonSep 2, 2025
What causes horizontal stripes on Brother MFC-9320CW All in One Printer output?
- M
  Michael HigginsSep 2, 2025
  If you're seeing horizontal stripes on your Brother All in One Printer prints, it could be caused by dirt on the charged electrode, a bend of the tray ground spring, toner attached on the develop roller, a scratch on the heat roller, or HVPS control PCB failure. You can try cleaning both electrodes. If the issue continues, replace the paper tray or the fuser unit. This problem might disappear by printing approximately 10 pages; if it does not, replace the toner cartridge. If the problem still occurs, replace the HVPS control PCB ASSY.
G
Gary BrownSep 15, 2025
Why are there one color spots or dirt on prints from my Brother All in One Printer?
- A
  Amanda AlexanderSep 15, 2025
  If you notice one color spots or dirt appearing on prints from your Brother All in One Printer, it could be due to fuser unit failure or toner/new sensor PCB failure. Consider replacing the fuser unit or the toner/new sensor PCB ASSY.
M
michaelmayAug 31, 2025
Why does my Brother MFC-9320CW All in One Printer have vertical streaks on printouts?
- C
  Cameron RomeroAug 31, 2025
  If you're experiencing vertical streaks on your printouts from your Brother All in One Printer, it could be due to dirt in the paper feed system, a dirty exposure drum, a bend in the tray ground spring, a scratch on the heat roller, or a LED ASSY failure. Try wiping off any dirt from the paper feed system and cleaning the drum unit. If the issue continues, you may need to replace the paper tray, the fuser unit, or the LED ASSY.
J
Janice MunozSep 18, 2025
What causes hollow prints on my Brother MFC-9320CW All in One Printer?
- L
  Lisa NewmanSep 18, 2025
  If your Brother All in One Printer is producing a hollow print, it could be due to fuser unit failure. Replace the fuser unit.
L
ljohnsonSep 16, 2025
Why is the color density unstable on my Brother MFC-9320CW All in One Printer prints?
- A
  Amanda SimmonsSep 17, 2025
  If your Brother All in One Printer is experiencing unstable color density, it could be due to drum unit conduction failure, toner cartridge conduction failure, dirt on the belt unit electrode, engine PCB failure, HVPS control PCB failure, high-voltage power supply PCB failure, LED head control PCB failure, or main PCB failure. Try cleaning both electrodes. If the issue persists, replace the engine PCB ASSY, the HVPS control PCB ASSY, the high-voltage power supply PCB ASSY, the LED head control PCB ASSY, or the main PCB ASSY.
A
anthonydennisSep 23, 2025
What to do if CD-ROM does not start automatically for Brother Print Server?
- L
  Linda KingSep 23, 2025
  If the CD-ROM with the Brother print server software doesn't start automatically, execute Start.exe in the root directory of the CD-ROM or reset the print server back to its factory default settings.
R
Ryan FisherAug 28, 2025
Why is the printout from my Brother All in One Printer too light on the whole page?
- N
  Nicholas RuizAug 28, 2025
  If your Brother All in One Printer is producing a light image on the whole page, it could be due to several reasons. It might be caused by a failure of the HVPS control PCB, the high-voltage power supply PCB, the engine PCB, the main PCB, the LED head control PCB, the LED ASSY, or the registration mark L PCB. To resolve this, the suggested solution is to replace the corresponding faulty ASSY.
P
Parker CastanedaAug 27, 2025
What to do if print job is not printed with Brother Print Server?
- M
  Melissa DavidsonAug 27, 2025
  If your print job is not being printed with your Brother print server, it could be due to mismatched or duplicate IP addresses. Verify that the print server is on your network.
R
Robert SullivanAug 26, 2025
How to solve Brother Print Server not found during network print software setup?
- S
  smithtylerAug 27, 2025
  If the Brother print server is not found during the network print software setup or printer driver installation in Windows, ensure that you have configured the IP address settings of the Brother print server. Refer to Chapter 2 of the User's Guide for instructions before proceeding with the installation.
C
Cory KellyAug 25, 2025
What to do if there is an error during printing with Brother Print Server?
- D
  Diana SantiagoAug 26, 2025
  If you are experiencing errors during printing with your Brother print server, it could be because the printer is busy processing large print jobs from other users. Please try to execute your print job again after the other jobs are completed.

Brother MFC-9320CW Specifications

General

Duplex printing	Yes
Print technology	LED
Maximum resolution	2400 x 600 DPI
Time to first page (black, normal)	15 s
Time to first page (color, normal)	16 s
Print speed (black, normal quality, A4/US Letter)	16 ppm
Scan to	e-mail, FTP, OCR
Scanner type	Flatbed scanner
Grayscale levels	256
Input color depth	48 bit
Optical scanning resolution	1200 x 2400 DPI
Copier resize	25 - 400 %
Maximum copy resolution	600 x 600 DPI
Maximum number of copies	99 copies
Time to first copy (black, normal)	19 s
Time to first copy (color, normal)	24 s
Copy speed (black, normal quality, A4)	16 cpm
Faxing	Color faxing
Fax memory	500 pages
Modem speed	33.6 Kbit/s
Fax speed dialing (max numbers)	200
Total input capacity	250 sheets
Total output capacity	100 sheets
Auto document feeder (ADF) input capacity	35 sheets
Internal memory	64 MB
Card reader integrated	No
Sound power level (standby)	30 dB
Sound pressure level (printing)	53 dB
Display	LCD
Market positioning	Business
Display number of lines	2 lines
Display number of characters	16
Dimensions (WxDxH)	491 x 428 x 401 mm
All-in-one functions	Copy, Fax, Scan
Maximum internal memory	0.576 GB
Color all-in-one functions	copy, fax, print, scan
Security algorithms	128-bit WEP, 64-bit WEP, EAP, WPA-AES, WPA-PSK, WPA-TKIP
Standard interfaces	USB 2.0
USB 2.0 ports quantity	1
Power consumption (off)	12 W
Power consumption (standby)	72 W
Power consumption (average operating)	480 W
Maximum print size	216 x 356 mm
Paper tray media types	Bond paper, Envelopes, Labels, Plain paper, Recycled paper
Non-ISO print media sizes	Executive (184 x 267mm), Folio (media size), Legal (media size), Letter (media size)
ISO A-series sizes (A0...A9)	A4, A5, A6
ISO B-series sizes (B0...B9)	B5, B6
Maximum ISO A-series paper size	A4
Multi-Purpose Tray media weight	60 - 163 g/m²
Package weight	29000 g
Maximum duty cycle	1500 pages per month
Sustainability certificates	ENERGY STAR