EasyManuals Logo

Brother MFC-J2330DW User Manual

Brother MFC-J2330DW
814 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #419 background imageLoading...
Page #419 background image
If you configure your machine using EAP-TLS authentication, you must install the client certificate
issued by a CA before you start configuration. Contact your network administrator about the client
certificate. If you have installed more than one certificate, we recommend writing down the certificate
name you want to use.
If you verify your machine using the common name of the server certificate, we recommend writing
down the common name before you start configuration. Contact your network administrator about the
common name of the server certificate.
2. Press [Settings] > [All Settings] > [Network] > [WLAN] > [Setup Wizard].
3. When [Enable WLAN?] appears, press [Yes].
This will start the wireless setup wizard. To cancel, press [No].
4. The machine searches for your network and displays a list of available SSIDs. Swipe up or down or press a
or b to display [<New SSID>]. Press [<New SSID>], and then press [OK].
5. Enter the SSID name, and then press [OK].
For more information about how to enter text, see the Appendix.
6. Press [Infrastructure] when instructed.
7. Select the Authentication Method.
8. Do one of the following:
If you selected the [LEAP] option, enter the user ID, and then press [OK]. Enter the Password, and then
press [OK].
If you selected the [EAP-FAST], [PEAP] or [EAP-TTLS] option, select the Inner Authentication method
[NONE], [CHAP], [MS-CHAP], [MS-CHAPv2], [GTC] or [PAP].
Depending on your Authentication method, the Inner Authentication method selections differ.
Select the encryption type [TKIP+AES] or [AES].
Select the verification method [No Verification], [CA] or [CA + Server ID].
- If you selected the [CA + Server ID] option, enter the server ID, user ID and password (if
required), and then press [OK] for each option.
- For other selections, enter the user ID and Password, and then press [OK] for each option.
If you have not imported a CA certificate into your machine, the machine displays [No Verification].
If you selected the [EAP-TLS] option, select the encryption type [TKIP+AES] or [AES].
The machine will display a list of available Client Certificates, and then select the certificate.
Select the verification method [No Verification], [CA] or [CA + Server ID].
- If you selected the [CA + Server ID] option, enter the server ID and user ID, and then press [OK]
for each option.
- For other selections, enter the user ID, and then press [OK].
If you have not imported a CA certificate into your machine, the machine displays [No Verification].
9. The machine attempts to connect to the wireless device you have selected.
If your wireless device is connected successfully, the display shows [Connected].
You have completed the wireless network setup. To install drivers and software necessary for operating your
device, insert the Brother installation disc into your computer or go to your model's Downloads page on the
Brother Solutions Center at
support.brother.com.
412

Table of Contents

Other manuals for Brother MFC-J2330DW

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Brother MFC-J2330DW and is the answer not in the manual?

Brother MFC-J2330DW Specifications

General IconGeneral
Print TechnologyInkjet
FunctionsPrint, Copy, Scan, Fax
ConnectivityUSB, Ethernet, Wi-Fi, Wi-Fi Direct
Scan Resolution1200 x 2400 dpi
Fax Speed33.6 kbps
Max Print Resolution4800 x 1200 dpi
Print Speed (Black)22 ppm
Print Speed (Color)20 ppm
Duplex PrintingAutomatic
Display2.7" Touchscreen
ADF Capacity50 sheets
Supported Paper SizesA3, A4
Operating System SupportWindows, macOS, Linux
Scanner TypeFlatbed, ADF
Mobile PrintingBrother iPrint&Scan, AirPrint, Google Cloud Print
Ink CartridgesBlack, Cyan, Magenta, Yellow
Paper Input Capacity250 sheets

Related product manuals