Burk ARC Plus SL - Timeout Settings

94 pages

Save Page as PDF

To Next Page

To Previous Page

TIMEOUT SETTINGS

Edit>Settings>Site Settings - Timeouts

After certain connection errors, AutoLoad Plus, AutoPilot and the ARC Plus SL will log events and/or display error

messages. The Web interface will log off after the specified inactivity period Timeout durations are user-

configurable in the Timeouts tab.

Main Page

Using this Manual3
About the ARC Plus System4
ARC Plus Models4
New in Firmware Version 5.0.8.15
New in Firmware Version 5.0.5.15
New in Firmware Version 5.0.3.55
New in Firmware Version 5.0.2.65
New in Firmware Version 5.0.2.15
New in Firmware Version 5.0.1.216
New in Firmware Version 56
New in Firmware Version 36
Table of Contents8
Contents8
Introduction11
- Front Panel11
- Rear Panel12
Inputs and Outputs13
- Plus-X Ethernet I/O13
- Plusconnect™ Direct Transmitter Interfaces13
Communications14
- Autoload Plus Software14
- Autopilot® Software15
- Web-Based Monitoring and Control15
Software and Firmware Updates15
System Security15
Operation16
Web Page16
- Requirements16
- Security17
- Logging in and out17
- Navigating the Web Page17
- Smartphone Web Page20
Installation21
Needed Items21
Recommended Sequence21
Rear Panel Connections22
- Connecting to the Ethernet22
Initial Settings22
- Network Settings22
Configuration23
Using Autoload Plus Software23
Connecting to the ARC PLUS SL23
Saving and Archiving ARC Plus SL Configurations24
- Saving Configuration Changes to the ARC Plus SL24
- Archiving ARC Plus SL Settings to the PC24
- Uploading Archived Settings24
- Uploading Firmware24
Connecting Plus-X I/O Units25
Changing the Site Name25
Managing Users26
Time Settings27
Network Settings28
SNMP Settings29
- ARC Plus SL as an SNMP Manager29
- ARC Plus SL Trap Generationstatus Channel Source33
Email and Dial-Out Notifications36
- Configuring Email Alarm Notifications37
- Email Settings37
- Email Lists39
- Configuring Dial-Out Alarm Notifications39
- Dial-Out Lists40
Site Settings41
- Startup Behavior41
- Timeout Settings42
- Front Panel Behavior43
- Alarms44
- Events45
- Primary/Backup RSI Configuration45
- Web Interface46
- Modem Settings46
- Authorization Codes47
- Captures47
- Hiding Unused Channels50
Configuring an ARC Plus Network (Multi-Site Installations)51
- Adding Sites to the Network51
- Categorizing Sites51
- Setting the Network Password51
Macro Presets52
Site Speech Label52
Meters53
Meter Channels53
- Channel and Units Labels53
- Meter Type54
- Voltage Range54
- Sample Type and Time54
- Decimal Places54
- Meter Channel Source55
Meter Graph56
Meter Alarms57
- Delayed Alarm Reporting57
- Rearm Delay57
- Enabling/Disabling Alarms58
- Setting Limits58
Meter Actions59
Meter Notifications60
Meter Display61
Meter Speech Labels62
Calibrating Meter Inputs63
Status64
Status Channels64
- Inverting a Status Channel64
- Status Channel Source65
Status Alarms66
- Enabling/Disabling Alarms66
- Delayed Alarm Reporting67
- Rearm Delay67
- Alarm Severity67
- Alarm Priority67
Status Actions68
Status Notifications69
Status Display69
Status SPEECH Labels70
Commands70
- Momentary or Latching Relays70
- Command Duration70
- Command Labels71
- Command Source72
Virtual Channels75
Primer75
Examples76
- Status Values in Meter Channels76
- Min/Max/Average76
- Transmitter Efficiency76
- Meter Validation77
- Status Based on Analog Limits77
- Status for Multiple Events77
- Command Fault Checking78
- VSWR Computation78
Macros79
Macro Primer79
- Branching79
- Actions79
- IF Statements79
- Examples81
Macro Expressions85
- General85
- ARC Plus85
- Date and Time85
- Memory86
- Macros86
- Misc86
Starting and Stopping Macros87
- Autopilot87
- WEB Page87
- Raise and Lower Buttons87
- Status Actions88
- From a Macro88
- Macro Schedule88
Configuration90
- Calendar90
- Email Templates91
Creating Macros92
- Macro Editor92
- Saving Macros93
Appendix A: Specifications94

Burk ARC Plus SL - Timeout Settings

Table of Contents