What to do if Burkert Measuring Instruments display 'ERROR 4'?
If your Burkert Measuring Instruments display 'ERROR 4', it means there's a memory read error, and the totalizer values are lost. Press the ENTER key to acknowledge the error. The values of the totalizers are set to those of the last start of the device. Check the values of the totalizers.
What to do if Burkert Measuring Instruments display 'ERROR 6'?
If your Burkert Measuring Instruments display 'ERROR 6', it means there's a memory read error, and the totalizer values are lost. Press the ENTER key to acknowledge the error: the totalizers are reset.
What to do if my Burkert Measuring Instruments display 'PU H LIM'?
If your Burkert Measuring Instruments display 'PU H LIM', it means the pulse value times the K factor of the device is greater than 1000000, indicating that the entered volume for a pulse is too high. Enter a lower volume per pulse and check the K factor value.
What does 'PU L LIM' mean on Burkert Measuring Instruments?
If your Burkert Measuring Instruments display 'PU L LIM', it indicates that the pulse value times the K factor of the device is less than 1, meaning the entered volume for a pulse is too low. Enter a higher volume per pulse and check the K factor value.
What to do if my Bürkert Transmitter displays ERROR 5?
If your Bürkert Transmitter displays 'ERROR 5', it means there's a memory read error, and both the user settings and totalizer values are lost. To address this, press the ENTER key to acknowledge the error. The device will then operate with the default settings, and the totalizer values will be set to those of the last start. You should then adjust the device again and check the totalizer values. If the message appears frequently, it is recommended to send the device back to your supplier.
What to do if my Bürkert Measuring Instruments display shows 'LOW BATT'?
If your Bürkert Measuring Instruments display shows 'LOW BATT,' it means the battery power is too low and the device isn't working. You should replace the batteries.
What does "MEAS. OVF" mean on Bürkert Measuring Instruments and how to fix it?
If the Bürkert Measuring Instruments shows 'MEAS. OVF', the rotational frequency of the paddle wheel is higher than 250 Hz. Check and adjust the flow rate in the pipe if necessary.
What does 'ERROR3' mean on Bürkert Measuring Instruments and how to fix it?
If your Bürkert Measuring Instruments displays 'ERROR3', it means the user settings are lost, and the device might measure incorrect values. Try restarting the device. If the message continues, reconfigure the device.
What does 'ERROR4' mean on Bürkert Measuring Instruments and how to fix it?
If your Bürkert Measuring Instruments displays 'ERROR4', it means the totalizer values are lost, and the values saved upon the next to last power down are retrieved. Try restarting the device.
What does 'ERROR6' mean on Bürkert Measuring Instruments and how to fix it?
If the Bürkert Measuring Instruments displays 'ERROR6', it means totalizer values are definitely lost and both totalizers are reset. Start the device again.
Guidance on manual usage, symbols, and document validity.
Specifies the device's designed purpose and operational limitations.
Critical safety warnings for device operation, installation, and use.
Details the intended use and scope of the device's functionality.
Describes the physical build and different versions of the device.
Explains the markings and data presented on the device's name plate.
Comprehensive technical specifications for the 8025 Batch compact version.
Technical specifications for the 8025 Batch panel-mounted version.
Technical specifications for the 8025 Batch wall-mounted version.
Technical specifications for the SE35 Batch dosing controller.
Technical specifications for the 8035 Batch dosing controller.
Technical specs for SE35 Batch with specific sensor fittings.
Critical safety instructions for fluid installation.
Step-by-step guide for installing the compact 8025 Batch.
Installation guides for 8035 and SE35 Batch units.
Guide for installing the 8025 Batch in a panel.
Instructions for wall-mounting the 8025 Batch.
Safety precautions and cable requirements for electrical work.
Ensuring proper grounding for electrical safety.
Mapping of terminals and configuration of device selectors.
Specific wiring instructions for different device models and outputs.
Safety warnings and step-by-step guide for initial device setup.
Safety guidelines and overview of device operational modes.
Using navigation keys and understanding device menus.
How to configure various device parameters.
Steps for testing device inputs, outputs, and functions.
Accessing logs, viewing messages, and remote consultation.
Safety precautions and device cleaning instructions.
Resolving problems based on device LED indicators (OFF, RED, ORANGE).
Solutions for issues occurring during dosing or with warning messages.
Guidelines for safe handling, shipping, and storing the device.
Environmentally responsible methods for disposing of the device.
General| Display | LCD |
|---|---|
| Protection Class | IP65 |
| Output | 4-20 mA |
| Output Signal | 4-20 mA |
| Material | Stainless steel |
| Operating Temperature | -15 to +80 °C (depending on material) |
To Next Page
