68
PRSCAL04 12H 22 //MAINMENU/MAINTAIN/
1 cal_en 0 to 1 0 - Di Press Calibration 0 1 x
2 cur_pres 0 PSIG Current Pressure
3 cal_p1 0 PSIG Calib Pres1(0 PSIG) x
4 cal_p2 0 PSIG Calib Pres2(100-250PSIG) x
5 cal_s 0 - Calibrated Slope
6 cal_i 0 - Calibrated Intercept
7 cal_st 0 to 1 0 - Calibration Completed 0 1
PRSCAL05 12H 23 //MAINMENU/MAINTAIN/
1 cal_en 0 to 1 0 - Oil Sump Press Cali 0 1 x
2 cur_pres 0 PSIG Current Pressure
3 cal_p1 0 PSIG Calib Pres1(0 PSIG) x
4 cal_p2 0 PSIG Calib Pres2(100-250PSIG) x
5 cal_s 0 - Calibrated Slope
6 cal_i 0 - Calibrated Intercept
7 cal_st 0 to 1 0 - Calibration Completed 0 1
PRSCAL06 12H 24 //MAINMENU/MAINTAIN/
1 cal_en 0 to 1 0 - Oil Supply Press Cali 0 1 x
2 cur_pres 0 PSIG Current Pressure
3 cal_p1 0 PSIG Calib Pres1(0 PSIG) x
4 cal_p2 0 PSIG Calib Pres2(100-250PSIG) x
5 cal_s 0 - Calibrated Slope
6 cal_i 0 - Calibrated Intercept
7 cal_st 0 to 1 0 - Calibration Completed 0 1
VFD_OUT 13H 19 //MAINMENU/CONFIG/
1 hdpv_out 0 to 22 0 mA Head Pressure Reference 0 22
2 vfd_out 0 to 100 0 % Target VFD Speed 0 100
3 vfdstart 0 to 1 0 - VFD Start 0 1
4 tripr 0 to 1 0 - Shunt Trip Relay 0 1
5 ref_cool 0 to 1 0 - Refrigerant Cool Relay 0 1
6 treset 0 to 1 0 - VFD Fault Reset 0 1
7 freezrel 0 to 1 0 - Freeze Release 0 1
8 read_cfg 0 to 1 0 - Read Conguration 0 1
CFG_19DV 13H 20 //MAINMENU/CONFIG/
1 mot_pol 0 to 1 0 - Motor Pole Pair 0 1
2 - Single=0, Double=1
3 gv2_lim 30 to 100 96 % IGV2 Travel Limit 30 100
4 gv2_dmin 0 to 20 2 - IGV2 Minimum Degree 0 20
5 gv2_dful 10 to 100 90 - IGV2 Fully Open Degree 10 100
6 gv2_dmax 90 to 120 94 - IGV2 Actuator Max Deg 90 120
7 gv2_d20 0.0~120.0 28.1 - IGV2 Deg @IGV1 20 Deg 10 30
8 gv2_d30 0.0~120.0 37.2 - IGV2 Deg @IGV1 30 Deg 10 50
9 gv2_d50 0.0~120.0 71.6 - IGV2 Deg @IGV1 50 Deg 10 80
10 vfd_ratf 10 to 200 80 Hz VFD Rate Speed Hz 10 200
11 reg_tim 120 min Purge Regen Lasting Time
12 pgpumplm 600 min Daily PG Pumpout Limit
To Next Page
Loading...
