How to fix 'current weight deviates from zero range' error on CAS CI-2001B?
If your CAS Accessories scale shows that the current weight deviates from the zero range, you can press the ZERO key. Note that this only works if the deviation is within 10% of the maximum capacity.
How to calibrate CAS CI-2001B if zero range deviates?
If the zero range deviates from the set range on your CAS Accessories scale, first confirm that there is nothing on the weighing platform. If the platform is empty, perform a calibration in CAL mode.
What to do if the tare weight exceeds the maximum capacity on CAS CI-2001B?
If the tare weight exceeds the maximum capacity of your CAS Accessories scale, set the tare to be smaller than the maximum capacity.
How do I resolve load cell connection issues in CAS CI-2001B Accessories?
To resolve load cell connection issues in your CAS Accessories device, check the load cell connector to ensure the signal polarity is correct. If the load cell is damaged, it should be replaced.
What should I do if the weight on the CAS Accessories platform is too heavy?
If the weight on the platform of your CAS Accessories scale is too heavy to be measured, do not load items that exceed the maximum tolerance.
What if load cell output is too low or high during SPAN calibration on CAS Accessories?
If the load cell output is too low or too high during SPAN calibration on your CAS Accessories scale, proceed with calibration again using less resolution.
What to check if load cell output is too high at ZERO calibration on CAS Accessories?
If the load cell output is too high at ZERO calibration on your CAS Accessories scale, check if the platform is empty. Then, proceed with calibration again after checking in A/D TEST mode.
How to troubleshoot printer connection errors on CAS CI-2001B?
To troubleshoot printer connection errors with your CAS Accessories device, check the printer connector.
Why does my CAS CI-2001B scale show an error in calibration mode?
Errors during calibration of your CAS Accessories scale can stem from several reasons. One common cause is setting the resolution beyond the limit of 1/10,000; try lowering the resolution. Another reason might be that the weight used for span calibration is less than 10% of the scale's maximum capacity. In this case, set the weight for span calibration in CAL 3 to exceed 10% of the maximum capacity. Conversely, if the weight for span calibration surpasses 100% of the scale's maximum capacity, adjust it to be within the limit. If the load cell output is either too low or too high during SPAN calibration, attempt the calibration again with less resolution. If the load cell output is too high at ZERO calibration, ensure the platform is empty and repeat the calibration after checking in A/D TE...
What to do if my CAS CI-2001B scale shows an error in weighing mode?
If your CAS Accessories scale displays an error during weighing, several factors could be responsible. It could be due to a failure in the load cell connection or an error in the A/D conversion. Check the load cell connector, paying attention to the signal polarity. Another potential cause is an error in the printer connection, so inspect the printer connector. If the current weight deviates from the zero range, press the ZERO key, provided the deviation is within 10% of the maximum capacity. Also ensure that the tare weight does not exceed the scale's maximum capacity. If the zero range deviates from the set range, ensure the weighing platform is empty and perform calibration in CAL mode. Finally, make sure that the weight on the platform does not exceed the maximum tolerance. If the load...
Details of analog components, voltage, sensitivity, and resolution.
Specifications for digital display, size, and power consumption.
Details the function of each key on the front panel.
Details the function of each key on the front panel.
Instructions on how to activate the Test Mode.
Instructions on how to activate the Calibration Mode.
Instructions on how to activate the Set Mode.
Lists common errors encountered during weighing operations.
Load cell connection failure or A/D conversion error.
Error related to printer connection.
ZERO or TARE key adjustment issue under unstable condition.
Current weight deviates from zero range.
Tare weight exceeds the maximum capacity.
Zero range deviates from the set range.
Platform weight exceeds measurement tolerance.
Lists common errors encountered during calibration.
Resolution limit (1/10,000) exceeded.
Span calibration weight is too low (under 10% capacity).
Span calibration weight is too high (over 100% capacity).
Load cell output too small at SPAN calibration.
Load cell output too large at SPAN calibration.
Load cell output too large at ZERO calibration.
General| Brand | CAS |
|---|---|
| Model | CI-2001B |
| Category | Accessories |
| Language | English |
To Next Page
