To Next PageTo Next PageHow to troubleshoot main power problems in ClimateMaster Heat Pump?
If the green status LED is off on your ClimateMaster Heat Pump, check the line voltage circuit breaker and disconnect. Also, check for line voltage between L1 and L2 on the contactor, 24VAC between R and C on CXM/DXM2, and the primary/secondary voltage on the transformer.
How do I troubleshoot Condensate Fault Code 6 on my ClimateMaster Tranquility TSV 009 Heat Pump?
If your ClimateMaster Heat Pump shows Condensate Fault Code 6, check for blockage and clean the drain. Inspect the trap dimensions and ensure its location is ahead of the vent. Verify the piping slope is away from the unit and check the slope of the unit toward the outlet. Ensure proper venting by checking the vent location. Also, check for moisture shorting to the air coil and replace the air filter. If there is restricted return air flow, find and eliminate the restriction, and increase the return duct and/or grille size.
What to do if my ClimateMaster Tranquility TSV 009 Heat Pump shows HP Fault Code 2 High Pressure?
If your ClimateMaster Heat Pump displays a High Pressure fault (Code 2), the issue might stem from several causes. If cooling, check the pump or valve operation/setting and ensure proper water flow. Make sure the water temperature is within the specified range for cooling. If heating, inspect the air filter and clean or replace if dirty. Also, examine the fan motor operation for any airflow restrictions. Ensure the air coil is clean and that the external static pressure aligns with the blower table. Verify that the return air temperature is within the design parameters, and check superheat/subcooling against the typical operating condition table. Finally, check the switch continuity and operation, replacing if necessary.
What causes LP/LOC Fault Code 3 Low Pressure / Loss of Charge in ClimateMaster Tranquility TSV 009?
If your ClimateMaster Heat Pump shows a Low Pressure/Loss of Charge fault (Code 3), it may be due to insufficient charge. Check for refrigerant leaks. Also, check the charge and start-up water flow.
What does Over/Under Voltage Code 7 mean on my ClimateMaster Heat Pump?
If your ClimateMaster Heat Pump displays an Over/Under Voltage fault (Code 7), check the power supply and 24VAC voltage, both before and during operation. Inspect the power supply wire size. Consider whether a hard start kit is needed for the compressor. Also, check the 24VAC and unit transformer tap for correct power supply voltage. This applies to both undervoltage and overvoltage scenarios.
How to fix LT1 Fault Code 4 Water coil low temperature limit in ClimateMaster Heat Pump?
If your ClimateMaster Heat Pump displays a Water coil low temperature limit fault (LT1 Fault Code 4), it could be due to several reasons. If heating, check the pump operation or water valve operation/setting for reduced or no water flow. Ensure that the strainer or filter is not plugged, clean or replace if necessary. Also, check and adjust the water flow to the proper rate. If using antifreeze, check the antifreeze density with a hydrometer. If needed, clip the JW3 jumper for antifreeze (10°F [-12°C]) use. Ensure the water temperature is within the design parameters and check the temperature and impedance correlation per the chart.
What causes LT2 Fault Code 5 Air coil low temperature limit in ClimateMaster Tranquility TSV 009 Heat Pump?
If your ClimateMaster Heat Pump displays an Air coil low temperature limit fault (LT2 Fault Code 5), check for a dirty air filter and clean or replace it if necessary. Verify the fan motor operation and airflow isn't restricted. Also, check the external static pressure against the blower table. If the air temperature is out of range, ensure that the entering air temperature is within design parameters. If the temperature limit setting is improper (30°F vs 10°F [-1°C vs -12°C]), note that normal airside applications will require 30°F [-1°C] only. Finally, check the temperature and impedance correlation per the chart.
Why does my ClimateMaster Tranquility TSV 009 unit short cycle?
If your ClimateMaster Heat Pump is short cycling, start by checking and cleaning the air filter. Also, ensure the unit isn't in 'test mode'; if it is, reset the power or wait 20 minutes for it to automatically exit. Check the sizing for the actual load of the space. Finally, check the compressor overload and replace if necessary.
Why does only the fan run on my ClimateMaster Tranquility TSV 009?
If only the fan is running on your ClimateMaster Heat Pump, first ensure the thermostat is set for heating or cooling operation. Check for any lockout codes and reset the power. Inspect the compressor overload and replace if necessary. Finally, check the thermostat wiring at the heat pump, jumpering Y and R for compressor operation in test mode.
What does Unit Performance Sentinel Code 8 mean for ClimateMaster Heat Pump?
If your ClimateMaster Heat Pump displays Unit Performance Sentinel Code 8, it could indicate a few issues. If in heating mode and LT2 is greater than 125°F [52°C], check for poor air flow or an overcharged unit. If in cooling mode and LT1 is greater than 125°F [52°C] or LT2 is less than 40ºF [4ºC], check for poor water flow or air flow.
General| Type | Water Source Heat Pump |
|---|---|
| Cooling Capacity | 9, 000 BTU/h |
| Refrigerant | R-410A |
| Phase | 1 |
| Liquid Line Size | 3/8 in |
| Suction Line Size | 5/8 in |
Defines the unit model designation and series type.
Specifies the cooling/heating capacity range for the unit models.
Lists available voltage configurations for the unit.
Crucial safety instructions including DANGER, WARNING, CAUTION, and NOTICE.
Guidelines for unit preparation and site selection before installation.
Instructions for suspending units using hanger brackets and threaded rods.
Detailed guidelines for connecting water supply and return piping.
Requirements and calculations for using antifreeze in ground loops.
Guidelines for evaluating water quality for heat exchanger compatibility.
Compliance with electrical codes for field-installed wiring.
Guidelines for making line voltage connections to the unit.
Wiring procedures for connecting thermostats to control boards.
Field selection of temperature limits for water coil protection.
Best practices for thermostat placement and wiring connections.
Options for enabling and configuring dehumidification modes.
Utilizing test mode for system diagnostics and fault code retrieval.
Adjusting unit parameters using jumpers for specific configurations.
Configuring DXM2 operation via various DIP switch settings.
Procedure for initial unit startup and compressor delay sequences.
How the low pressure switch detects and reacts to abnormal conditions.
Protection against low water temperatures affecting the refrigerant circuit.
Protection against low air temperatures impacting unit performance.
How the ClimaDry® system functions in cooling, reheat, and heating modes.
Pre-power checks for unit components and wiring.
Verifying system water conditions, controls, and overall operation.
Diagnosing issues related to low refrigerant charge or pressure.
Identifying causes for reduced cooling or heating capacity.
Details of the warranty coverage for CM products internationally.
