T750SE Access Point
Quick Setup Guide
NOTE: The minimum sowar
e revision for the T750SE is ZoneDirector
(ZD) 10.4.1 or later, or SmartZone (SZ) 5.2 or later, or standalone AP
rmware 114.X or later.
This Quick Setup Guide provides step-by-step instrucons on ho
w to eld-
install the RUCKUS WIRELESS T750SE access point (AP). For detailed
informaon on planning the installaon, performing a site survey, and
operang the T750SE, refer to the RUCKUS WIRELESS Outdoor Access Point
User Guide, available at hps://support.ruckuswireless.com.
WARNING! Only trained and qualied per
sonnel should be allowed to
install, replace, or service this equipment.
WARNING! Inst
allaon of this equipment must comply with local and
naonal electrical codes.
CAUTION! Make sur
e that you form a 80mm - 130mm (3”-5”) drip loop
in any cable that is aached to the AP or the building. This will prevent
water from running along the cable and entering the AP or the building
where the cable terminates.
CAUTION! Be sure tha
t grounding is available and that it meets local
and naonal electrical codes. For addional lightning protecon, use
lightning rods and lightning arrestors.
CAUTION! Make sur
e that proper lightning surge protecon
precauons are taken according to local electrical code.
WARNING! RUCKUS WIRELE
SS strongly recommends that you wear eye
protecon before mounng the T750SE.
This Guide in Other Languages
• 请从以下网站获得该指南的简体中文版 hps://
support.ruck
uswireless.com.
• Vous trouverez la version française de ce guide à l'adresse suivante
hps://support.ruckuswireless.com.
• このガイドの日本語版は hps://support.ruckuswireless.com でご覧
ください。
• 이 가이드의 한국어 버전은 웹 사이트 (hps://
support.ruckuswireless.com) 에서 확인하시기 바랍니다.
• Veja a versão em português (Brasil) deste guia em hps://
support.ruckuswireless.com.
• Puede ver la versión en español (América Lana) de esta guía en
hps://support.ruckuswireless.com.
Before You Begin
Bef
ore deploying RUCKUS WIRELESSs products, please check for the latest
soware and the release documentaon.
• Release Notes and other user documentaon are available at hp://
support.ruckuswireless.com/documents.
• Soware upgrades are available at hp://support.ruckuswireless.com/
soware.
• Soware license and limited warranty informaon are available at
hp://support.ruckuswireless.com/warranty.
Before deploying your RUCKUS WIRELESS Access Point, verify that all
items listed in Package Contents are included in the package. If any item
is damaged or missing, nofy your authorized RUCKUS WIRELESS sales
representave. Also, make sure that you have the required hardware
and tools.
Required Hardware and Tools
• 1/2” (13 mm) at-blade screwdriver or equivalent
• No. 2 Phillips screwdriver
• Small at-blade screwdriver
• Torque wrench or torque screwdriver with sockets
• Long-nose pliers
• Electrical wire stripping and terminal crimping pliers
• Pipe, pole or a sturdy at surface
• Electric drill with drill bits and customer-supplied wall anchors, at
washers, and hex nuts for at-surface mount
Package Contents
A complete T750SE eld installaon package includes all of the items listed
below :
• T750SE Access Point
• M25 data cable gland extender
• Three M25 data cable glands
• Outdoor AP Mounng Bracket kit
• One ground wire with lug
• Cloud Management Statement
• Cable gland extender gasket
• AC Connector
• Zipcord cable gland grommet
• Four 1/2” (12.7 mm) wide adjustable clamps, 2.5” (63.5 mm) diameter,
for main mounng bracket on smaller poles
• Safety cable kit
• Service Level Agreement/Limited Warranty Statement
• Declaraon of Conformity
• Regulatory Statement
• RUCKUS WIRELESS AP Geng Started Guide
• This Quick Setup Guide
Mounng Instrucons
Connecng and Sealing the RJ-45 Cables
The T750SE may use zero, or one or two RJ-45 cables, one for Ethernet
when congured as a Root AP (RAP), and another when the T750SE is
supplying PoE out to a peripheral device, such as a small cell or micro cell
radio, and zero when using the SFP as a backhaul alternate with AC power.
When the T750SE uses RJ-45 cables, connect and seal the cables using the
M25 data cable glands as shown in Figure 2.
FIGURE 1 T750SE AP PoE IN and PoE OUT ports
1. SFP port
2. P
oE IN
3. PoE OUT
4. AC port
WARNING! Do not use any P
oE injector not tested and approved by
RUCKUS WIRELESS to power the T750SE Access Point.
WARNING! Do not plug PoE IN po
wer into the PoE OUT port. See Figure
1.
1. Feed the end of the cable through the gland dome, rubber grommet,
clamping ring assembly and cable gland base, as sho
wn in Figure 2.
NOTE: Do not seat the clamping ring and rubber gr
ommet into the
cable gland base unl the cable gland base has been torqued to
specicaons.
Copyright
©
2020 CommScope, Inc. All rights reserved. Page 1 of 7
Published July 2020, Part Number 800-72283-001 Rev B
To Next Page
Need help?
General
