Need help?Do you have a question about the CommScope Era CAP M 9 and is the answer not in the manual?
General| Category | Wireless Access Point |
|---|---|
| Antenna Type | Internal |
| MIMO Configuration | 2x2 |
| Ethernet Ports | 1 x 10/100/1000 Mbps |
| Supported Standards | 3GPP |
| Operating Temperature | -40°C to +55°C |
| Mounting | Wall |
| Model | CommScope Era CAP M 9 |
Provides information about the document's purpose, limitations, and subject to change.
States copyright ownership, reproduction restrictions, and lists trademarks.
Details the changes and updates made in this release of the installation guide.
Explains the icons used for warnings, cautions, and notes in the document.
Lists and defines abbreviations used throughout the installation guide.
Explains the format of CommScope part numbers and how to find the latest release.
Describes the CAN's role in signal distribution and its two configuration modes: Classic and Switching.
Explains WIN's function as an interface for remote signal sources in C-RAN.
Details the TEN as an expansion node connecting to the CAN via fiber.
Defines Access Points (APs) and their role in connecting to antennas and wireless devices.
Provides a description of the CAP M, its interfaces, and RF coverage capabilities.
Details the CAP M's passive cooling, operating temperature, IP rating, and power consumption.
Identifies and describes the connectors and LEDs on the CAP M unit.
Explains the function and usage of the Notch-Filter connectors on the CAP M.
Describes the Single Mounting Bracket for wall or vertical surface mounting.
Details the Dual Mounting Bracket for mounting two CAP Ms back-to-back.
Covers the Pole Mounting Kit for securing the CAP M to poles up to 18 inches in circumference.
Explains the Hybrid Fiber Splice Box for separating power and fiber signals.
Lists and describes the OCTIS Kit options for interfaces and auxiliary devices.
Provides safety warnings related to RF energy exposure during operation.
Outlines essential safety measures for handling equipment and avoiding electrical or laser hazards.
Lists warnings to prevent property damage, including temperature and material considerations.
Details general safety requirements for installation, including electrical shock and RF exposure.
Explains how to prevent damage to hardware from Electro-Static Discharge (ESD).
Covers FCC and ISED compliance requirements, including RF exposure and antenna gain limits.
Explains symbols used on equipment and their associated compliance meanings.
Details the rules and procedures for installing and cascading CAP M units.
Specifies requirements for using Cat6A cables with Ethernet devices connected to a Fiber CAP L.
Lists steps to take before beginning the CAP M installation process.
Lists the tools and materials required for installation, which are not supplied by CommScope.
Guides on how to calculate the power consumption of the CAP M unit.
Provides guidelines for selecting a suitable mounting site for the CAP M.
Details the procedure for unpacking and inspecting the CAP M and its accessories.
Provides instructions for wiring the optional Hybrid Fiber Splice Box.
Specifies the required mounting orientation for the CAP M for proper ventilation.
Describes how to mount the CAP M to a wall or vertical surface using available brackets.
Details the steps for mounting a CAP M using a single wall-mounting bracket.
Provides instructions for mounting two CAP Ms back-to-back using a dual mounting bracket.
Details the procedure for mounting the CAP M to a pole using the pole mounting kit.
Explains how to attach the optional Hybrid Fiber Splice Box to the CAP M.
Provides steps for attaching the splice box for single mount installations.
Details the process of attaching the splice box for dual mount installations.
Details the procedure for grounding the CAP M chassis for safety and protection.
Guides on connecting various cables to the CAP M unit.
Lists the cable materials required for installation and how to obtain them.
Provides instructions for connecting the CAP M to a passive antenna using coaxial cable.
Details how to connect the CAP M Optical Port 1 to a Classic CAN or TEN.
Explains how to connect a secondary CAP M using Optical Port 2.
Describes how to connect an external Ethernet device to the CAP M via Port A.
Details the procedure for powering the CAP M unit, including safety precautions.
Describes the specifications and connections for the CAP M AC power cable.
Details the specifications and connections for the CAP M DC power cable.
Outlines the steps for connecting power to the CAP M unit.
Provides detailed instructions for connecting the mains power to the CAP M.
Details how to connect the power and fiber for a CAP M powered by a Hybrid Fiber Splice Box.
Explains the CAP M power-on sequence and the behavior of the Power LED.
Provides contact information for CommScope's Distributed Coverage and Capacity Solutions Technical Support.
Guides on how to access CommScope's DCCS Support Request website for tickets.
Information on CommScope's recycling program for WEEE compliant equipment.
Provides access to minimum software requirements for DCCS hardware modules.
Guides on accessing and enrolling in CommScope's online DAS and Small Cell Institute training.
Details how to access DCCS user documentation via the CommScope Customer Portal.
To Next Page
