What to do if I cannot change screens or setpoints on Crestron CHV-THSTAT Thermostat?
If you cannot change screens or setpoints on your Crestron Thermostat, local operation may be locked out. Remove the lockout from the network.
Why temperature offset value not affecting Cresnet outputs on Crestron Thermostat?
If the temperature offset value is not affecting Cresnet outputs on your Crestron Thermostat, it is because the offset is only added to "RegulationTemp". Add the offset in the SIMPL program.
Why Cresnet Balance Point values out of range on Crestron Thermostat?
If the Cresnet Balance Point values are out of range on your Crestron Thermostat, verify the intended balance point settings, because the values of -1°, 91°F represent "Off" settings.
What to do if I cannot leave setup on Crestron CHV-THSTAT Thermostat?
If you cannot leave the setup on your Crestron Thermostat, the sensor configuration might not be valid. Ensure the sensor setup meets system requirements.
Why cannot enter Auto mode on Crestron Thermostat?
If you cannot enter Auto mode on your Crestron Thermostat, it's possible that Auto mode is disabled in setup. Select “N” for the Disable Auto Mode item on the “Other Settings” setup page.
What does “NetDown” mean on Crestron CHV-THSTAT?
If your Crestron Thermostat displays “NetDown”, it indicates that there is no Crestron program or the program does not have a device at this net address included in this system. Check the ID in the program and fix the program if needed.
Why wide temperature variance in single-setpoint auto mode on Crestron CHV-THSTAT?
If you notice a wide temperature variance in single-setpoint auto mode on your Crestron Thermostat, the auto deadband setting might be too high. Adjust the auto deadband setting in setup.
Why is heating/cooling not operating in single-setpoint auto mode on Crestron CHV-THSTAT?
If the heating or cooling is not operating in single-setpoint auto mode on your Crestron Thermostat, adjust the auto deadband and anticipator settings for smoother operation. This is due to a 20-minute system toggling lockout.
Why does Crestron CHV-THSTAT system cycle too quickly?
If your Crestron Thermostat system cycles too quickly, it could be due to an anticipator/regulation setting that is too low. Reprogram the anticipator/regulator setting.
What to do if Crestron CHV-THSTAT Thermostat displays error message?
If your Crestron Thermostat displays an error message and the equipment isn't operating, check the wiring and use low capacitance twisted-pair wiring if there are bad communications.
Details the key functionalities and features of the CHV-TSTAT/CHV-THSTAT.
Lists and describes Cresnet network connection pins.
Lists and describes pins for connecting remote sensors.
Describes the power connection terminals.
Details network wiring requirements and calculations for Cresnet runs.
Explains the unique identity code (Net ID) required for each network device.
Step-by-step guide to entering and navigating the thermostat setup menus.
General notes and important considerations for thermostat setup.
Defines various heating/cooling and slab system types.
Guide to configuring Heat/Cool systems including stages and air types.
Guide to configuring Heat Pump systems with Aux heat or Dual Fuel.
Guide to configuring the Slab 1 floor warming system.
Guide to configuring the Slab 2 single stage space heat system.
Guide to configuring the Slab 3 single stage heat system with limits.
Guide to configuring Slab 4A two stage heat/one stage cool system.
Guide to configuring Slab 4B two stage heat/one stage cool system.
Guide to configuring Slab 5A one stage heat/cool with floor warming.
Guide to configuring Slab 5B one stage heat/cool with floor warming.
Describes the main display screen showing temperature, mode, and set points.
Explains how to navigate through system mode, fan mode, and other screens using the MODE button.
Describes how to set the fan mode to AUTO or ON for continuous operation.
Explains how to enable or disable the humidifier function if equipped and enabled.
Shows the thermostat's connection status (ONLINE or HOLD) within the Cresnet system.
Allows updating temperature settings to all thermostats on the system.
Displays current indoor humidity and allows setpoint adjustment if enabled.
Shows outdoor temperature and humidity if sensors are connected and enabled.
Displays text messages sent from the control system.
Overview of D3 Pro for automatic programming of Crestron systems.
Guide to using SIMPL Windows for programming Crestron control systems.
Illustrates the slotted symbol used in SIMPL Windows for thermostat programming.
Details the signals and definitions for the Heat/Cool control slot.
Details the signals and definitions for the Humidity control slot.
Details the signals and definitions for the Slab control slot.
Details the signals and definitions for the Current System State slot.
Details the signals and definitions for the Display Functions slot.
Details the signals and definitions for the System Configuration slot.
Defines the meaning of the characters and options within the Viewport ID strings.
Provides common troubleshooting issues and their corrective actions for the thermostat.
Details the manufacturer's warranty terms, coverage, and limitations for Crestron products.
General| Brand | Crestron |
|---|---|
| Model | CHV-THSTAT |
| Category | Thermostat |
| Language | English |
To Next Page
