Custom Engineering KUBE II ETH - TECHNICAL SPECIFICATIONS: Emulation and Wi-Fi; Printer Specs: Emulation and Wi-Fi Adapter

53
TECHNICAL SPECIFICATIONS
NOTES:
(1) Respecting the regular schedule of clean-
ing for the device components.
(2) Referred to a standard CUSTOM receipt
(L=10cm, Density = 12,5% dots on).
(3) This speed is achieved in the following
test conditions:
• parameter “Speed/Quality” = “High
Speed”;
• parameter “Print Density” = “0%”;
• ambient temperature = 25°C;
• power supply = 24 Vdc.
(4) Possibility through fi rmware confi guration
up to 250 mm/sec. respecting the test
conditions described in note 3 and using
paper MITSUBISHI TL4000.
(5) For receipts with wide black zones is
recommended a 60W opzional power
supply cod. 963GE020000003.
(6) To set 60 columns (in a 20cpi den-
sity), change the right margin to 80mm
(640dot).
NOTE:
(1) Rispettando la regolare pianificazione
della pulizia delle parti del dispositivo.
(2) Riferito ad uno scontrino tipico CUSTOM
(L = 10cm, Densità = 12,5% dots accesi).
(3) Questa velocità è raggiunta nelle se-
guenti condizioni di test:
• parametro “Speed/Quality” = “High
Speed”;
• parametro “Print Density” = “0%”;
• temperatura ambiente = 25°C;
• tensione di alimentazione = 24 Vdc.
(4) Possibilità mediante configurazione
fi rmware di arrivare fi no a 250 mm/sec.
rispettando le condizioni di test riportate
nella nota 3 e utilizzando carta MITSUBI-
SHI TL4000.
(5) Per scontrini con ampie zone nere è con-
sigliato un alimentatore opzionale da 60W
minimo cod. 963GE020000003.
(6) Per impostare 60 colonne (con densità
20cpi), impostare il margine destro a
80mm (640dot).
HINWEISE:
(1) Die Einhaltung des regelmäßigen Zeit-
plan der Reinigung Teile des Gerätes.
(2) In Bezug auf einen Standard CUSTOM
Beleg (L=10cm, Dichte = 12,5% Dots an).
(3) Diese Geschwindigkeit wird in den
folgenden Testbedingungen erreicht:
• “Speed/Quality” parameter = “High
Speed”;
• “Print Density” parameter = “0%”;
• Raumtemperatur = 25°C;
• Versorgungsspannung = 24 Vdc.
(4) Mögliche Konfi guration mit Firmware
bis zu 250 mm / sec. Beobachten Sie
die Prüfbedingungen in Anmerkung 3
beschrieben und die Verwendung von
Papier MITSUBISHI TL4000.
(5) Für Belege mit großfl ächigen schwar-
zen Bereichen wird ein optionales
Netzgerät mit 60W empfohlen cod.
963GE020000003.
(6) Zur Einstellung von 60 Spalten (mit 20cpi
Dichte den rechten Rand auf 80mm stel-
len (640dot).
ESC/POS
TM
EMULATION
Character set 3
Character density 11 cpi 15 cpi 20 cpi
Number of columns 33 42 56
(6)
Character / sec 1815 2310 3080
Lines / sec 55 55 55
Characters (L x H mm)-Normal 2,25x3 1,75 x 3 1,25 x 3
WI-FI ADAPTER (cod. 972GU020000300) and ACCESS POINT (cod. 972GU010000301) SPECIFICATIONS
Standards IEEE802.11b
Wireless speed 11 Mbps
Protocol supported TCP/IP, IPX, NetBEUI
Security
40 bits and 128 bits WEP encryption
Access Control (MAC address fi lter)
Default button
Press the button during the power-on time to let the device operate at factory de-
fault settings.
LED indicators Ethernet active, Wireless transmits, AP active
Antenna Internal Diversity Antenna
Power supply DC 5V