EasyManua.ls Logo

Da-Lite Cosmopolitan Electrol - User Manual

Da-Lite Cosmopolitan Electrol
16 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
INSTRUCTION BOOK FOR
Cosmopolitan Electrol
For Sizes Up To 9' x 12'

Table of Contents

Questions and Answers

  • B
    Billy WhiteDec 1, 2025
    What to do if my Da-Lite Projector Accessories screen will not operate and the motor isn't humming?
    • D
      Dwayne HaynesDec 1, 2025
      If your Da-Lite Projector Accessories screen isn't working and the motor is silent, several issues could be the cause: * A blown fuse: Replace the fuse. * A tripped circuit breaker: Reset the breaker. * No power to the switch or junction: Check the power supply, tighten loose connections, and correct any improper connections. For the 'down' position, check for power across the black and white leads; for the 'up' position, check the red and white leads. * Thermal overload: Allow the motor to cool for 15 minutes before trying again. * Broken wire: Check for continuity and reconnect any broken wires. * Defective motor, limit switch, or capacitor: Replace the motor assembly, which is a sealed unit. * Temporary binding: Turn the roller by hand to free it. * Burned out capacito...
  • J
    jmcdanielAug 25, 2025
    What to do if my Da-Lite Cosmopolitan Electrol roller is displaced from the mounting bracket?
    • B
      Beth BarnettAug 26, 2025
      If the roller of your Da-Lite Projection Screen has become displaced from the mounting bracket, it might be that the pin end slipped out of the nylon bearing. To fix this, realign the pin end bracket.
  • B
    Bryan SchultzAug 27, 2025
    Why is my Da-Lite Projection Screen making noise?
    • M
      Mackenzie WoodsAug 27, 2025
      If your Da-Lite Projection Screen is making excessive noise, it may be due to gear noise. The suggested solution is to replace the motor assembly. Note that the screen will operate with a low pitched hum.
  • M
    Megan BrownAug 28, 2025
    What to do if my Da-Lite Cosmopolitan Electrol Projection Screen roller displaced from mounting bracket?
    • L
      Leah NelsonAug 29, 2025
      If the roller of your Da-Lite Projection Screen has become displaced from the mounting bracket, it may be because the pin end slipped out of the nylon bearing. Try to realign the pin end bracket.
  • J
    Jennifer WernerAug 30, 2025
    Why does my Da-Lite Cosmopolitan Electrol Projection Screen keep coasting?
    • C
      cheryl94Aug 30, 2025
      If your Da-Lite Projection Screen is coasting, it's likely due to a defective brake. The solution is to replace the motor assembly.
  • A
    alicia95Sep 18, 2025
    What to do if Da-Lite Whiteboard roller is displaced from mounting bracket?
    • M
      Maria OlsonSep 18, 2025
      If the roller of your Da-Lite Whiteboard is displaced from the mounting bracket, it's likely because the pin end slipped out of the nylon bearing. Remove the pin end mounting, realign the motor in the tube, and re-attach the pin end.
  • S
    Stephen RoseSep 15, 2025
    Why is my Da-Lite Whiteboard making noise?
    • A
      Angela HouseSep 15, 2025
      If your Da-Lite Whiteboard is making noise, it could be due to a squeaking rubber end plug rubbing on the motor (adjust the roller to the center of the case), a foreign object rubbing on the roller or fabric (remove the object), or gear noise (replace the motor assembly). A low-pitched hum during operation is normal.
  • X
    Xavier MarksSep 17, 2025
    What causes coasting in Da-Lite Whiteboard?
    • D
      Deborah SmithSep 17, 2025
      Coasting in your Da-Lite Whiteboard is typically caused by a defective brake. The suggested solution is to replace the motor assembly.
  • M
    Mrs. Claudia Moody MDSep 8, 2025
    What to do if my Da-Lite Cosmopolitan Electrol Projection Screen has an incorrect stopping position in upward direction?
    • M
      Melissa AllenSep 8, 2025
      If your Da-Lite Projection Screen stops at the wrong position when moving upwards, it could be due to a lost roller wrap. Another possibility is that the “up” limit switch is out of adjustment. If this is the case, adjust the 'up' limit switch.
  • A
    Antonio BrownSep 6, 2025
    What to do if the roller of my Da-Lite Projector Accessories screen is displaced from the mounting bracket?
    • R
      Rachel GutierrezSep 6, 2025
      If the roller of your Da-Lite Projector Accessories screen has come away from the mounting bracket, this may be because the pin end slipped out of the nylon bearing. To fix this, remove the pin end mounting, realign the motor in the tube, and re-attach the pin end.

Da-Lite Cosmopolitan Electrol Specifications

General IconGeneral
BrandDa-Lite
ModelCosmopolitan Electrol
CategoryProjection Screen
LanguageEnglish

Related product manuals