Danfoss VLT 6000 HVAC

VLT
®
6000 HVAC
137MG.60.B1.02 - VLT is a registered Danfoss trademark
✭ = factory setting. ( ) = parameter window text. [ ] = value for use in communication via serial communication port
Programming
TT
TT
T
erminal 54, analogue input [V], parameter 523:erminal 54, analogue input [V], parameter 523:
erminal 54, analogue input [V], parameter 523:erminal 54, analogue input [V], parameter 523:
erminal 54, analogue input [V], parameter 523:
Gives the voltage value of the signal on terminal 54.
TT
TT
T
erminal 60, analogue input [mA], parameter 524:erminal 60, analogue input [mA], parameter 524:
erminal 60, analogue input [mA], parameter 524:erminal 60, analogue input [mA], parameter 524:
erminal 60, analogue input [mA], parameter 524:
Gives the current value of the signal on terminal 60.
Pulse reference [Hz], parameter 525:Pulse reference [Hz], parameter 525:
Pulse reference [Hz], parameter 525:Pulse reference [Hz], parameter 525:
Pulse reference [Hz], parameter 525:
Gives a pulse frequency in Hz connected to one of
the terminals 17 and 29.
ExterExter
ExterExter
Exter
nal rnal r
nal rnal r
nal r
eferefer
eferefer
efer
ence, parameter 526:ence, parameter 526:
ence, parameter 526:ence, parameter 526:
ence, parameter 526:
Gives the sum of external references as a percentage
(sum of analogue/pulse/serial communication) in the
range from Minimum reference, Ref
MIN
to Maximum
reference, Ref
MAX
.
Status word, parameter 527:Status word, parameter 527:
Status word, parameter 527:Status word, parameter 527:
Status word, parameter 527:
Gives the present status word of the VLT frequency
converter in Hex.
Heat sink temperature, parameter 528:Heat sink temperature, parameter 528:
Heat sink temperature, parameter 528:Heat sink temperature, parameter 528:
Heat sink temperature, parameter 528:
Gives the present heat sink temperature of the VLT
frequency converter. The cut-out limit is 90 ± 5 °C,
while cutting back in is effected at 60 ± 5 °C.
Alarm word, parameter 529:Alarm word, parameter 529:
Alarm word, parameter 529:Alarm word, parameter 529:
Alarm word, parameter 529:
Gives a Hex code for the alarm on the VLT frequency
converter. See page 140 for further information.
Control word, parameter 530:Control word, parameter 530:
Control word, parameter 530:Control word, parameter 530:
Control word, parameter 530:
Gives the present control word of the VLT frequency
converter in Hex.
WW
WW
W
arar
arar
ar
ning worning wor
ning worning wor
ning wor
d, parameter 531:d, parameter 531:
d, parameter 531:d, parameter 531:
d, parameter 531:
Indicates in Hex whether there is a warning on the
VLT frequency converter. See page 140 for further
information.
Extended status word, parameter 532:Extended status word, parameter 532:
Extended status word, parameter 532:Extended status word, parameter 532:
Extended status word, parameter 532:
Indicates in Hex code whether there is a warning on
the VLT frequency converter. See page 140 for further
information.
Description of choices under parameters 509-523,
cont.:
User-defined read-out, parameter 513:User-defined read-out, parameter 513:
User-defined read-out, parameter 513:User-defined read-out, parameter 513:
User-defined read-out, parameter 513:
gives a user-defined value calculated on the basis of
the present output frequency and unit, as well as the
scaling in selected in parameter 005 Max. value of
user-defined read-out. The unit is selected in
parameter 006 Unit for user-defined read-out.
Motor current [A], parameter 514:Motor current [A], parameter 514:
Motor current [A], parameter 514:Motor current [A], parameter 514:
Motor current [A], parameter 514:
Gives the motor phase current measured as an
effective value.
Power [kW], parameter 515:Power [kW], parameter 515:
Power [kW], parameter 515:Power [kW], parameter 515:
Power [kW], parameter 515:
Gives the present power absorption of the motor in
kW.
Power [HP], parameter 516:Power [HP], parameter 516:
Power [HP], parameter 516:Power [HP], parameter 516:
Power [HP], parameter 516:
Gives the present power absorption of the motor in
HP.
Motor voltage, parameter 517:Motor voltage, parameter 517:
Motor voltage, parameter 517:Motor voltage, parameter 517:
Motor voltage, parameter 517:
Gives the voltage fed to the motor.
DC link voltage, parameter 518:DC link voltage, parameter 518:
DC link voltage, parameter 518:DC link voltage, parameter 518:
DC link voltage, parameter 518:
Gives the intermediate circuit voltage of the VLT
frequency converter.
Thermal load, motor [%], parameter 519:Thermal load, motor [%], parameter 519:
Thermal load, motor [%], parameter 519:Thermal load, motor [%], parameter 519:
Thermal load, motor [%], parameter 519:
Gives the calculated/estimated thermal load on the
motor. 100 % is the cut-out limit. See also parameter
117 Motor thermal protection.
Thermal prThermal pr
Thermal prThermal pr
Thermal pr
otection, VLotection, VL
otection, VLotection, VL
otection, VL
T [%], parameter 520:T [%], parameter 520:
T [%], parameter 520:T [%], parameter 520:
T [%], parameter 520:
Gives the calculated/estimated thermal load on the
VLT frequency converter. 100 % is the cut-out limit.
Digital input, parameter 521:Digital input, parameter 521:
Digital input, parameter 521:Digital input, parameter 521:
Digital input, parameter 521:
Gives the signal status of the 8 inputs (16, 17, 18, 19,
27, 29, 32 and 33). Input 16 corresponds to the bit to
the extreme left.
'0' = no signal, '1' = signal connected.
TT
TT
T
erminal 53, analogue input [V], parameter 522:erminal 53, analogue input [V], parameter 522:
erminal 53, analogue input [V], parameter 522:erminal 53, analogue input [V], parameter 522:
erminal 53, analogue input [V], parameter 522:
Gives the voltage value of the signal on terminal 53.