Danfoss VLT AQUA Drive FC 202

G
Ground
Connections.................................................................... 2-6, 3-2, 8-3
Loops................................................................................................ 2-11
Wire..................................................................................... 2-6, 3-2, 8-3
Grounded Delta................................................................................... 2-8
Grounding
Grounding.............................................. 2-6, 2-7, 2-8, 3-1, 3-2, 8-3
Using Shielded Cable.................................................................... 2-6
H
Hand
Hand........................................................................................... 3-6, 4-3
On................................................................................................ 3-6, 4-3
Harmonics.............................................................................................. 1-4
I
IEC 61800-3............................................................................................ 2-8
Induced Voltage.................................................................................. 2-5
Initialization........................................................................................... 4-4
Input
Current............................................................................................... 2-8
Disconnect........................................................................................ 2-8
Power.............................. 1-4, 2-5, 2-6, 2-8, 3-1, 3-2, 8-1, 8-3, 9-1
Signal.................................................................................................. 5-2
Signals................................................................................... 2-11, 2-12
Terminals............................................................... 2-3, 2-8, 2-12, 3-1
Voltage....................................................................................... 3-3, 8-1
Installation............................. 1-3, 2-1, 2-2, 2-5, 2-10, 2-13, 3-2, 3-3
Isolated Line Power............................................................................ 2-8
J
Johnson Controls N2®..................................................................... 2-13
L
Leakage Current.................................................................................. 3-1
Lifting...................................................................................................... 2-2
Line
Power.................................................................................................. 2-5
Power Supply...................................................................... 10-2, 10-7
Power Supply (L1, L2, L3)........................................................ 10-12
Power Supply 1 X 200–240 V AC............................................ 10-1
Local
Control............................................................................... 4-1, 4-3, 7-1
Control Panel................................................................................... 4-1
Control Test...................................................................................... 3-6
Mode................................................................................................... 3-6
Operation.......................................................................................... 4-1
Start..................................................................................................... 3-6
M
Main Menu.................................................................................... 4-2, 5-1
Manual Initialization.......................................................................... 4-4
Mechanical Brake Control.............................................................. 2-12
Menu
Keys............................................................................................. 4-1, 4-2
Structure........................................................................... 4-3, 5-5, 5-4
Modbus RTU....................................................................................... 2-13
Motor
Cables................................................................................ 2-1, 2-5, 2-6
Current.............................................................................. 1-4, 3-5, 4-2
Data............................................................................................. 3-6, 3-5
Frequency......................................................................................... 4-2
Output........................................................................................... 10-12
Power......................................................................... 2-3, 2-5, 2-6, 4-2
Protection............................................................................ 2-5, 10-12
Rotation..................................................................................... 3-6, 4-2
Speeds................................................................................................ 3-3
Status.................................................................................................. 1-3
Wiring........................................................................ 2-5, 2-6, 3-2, 8-3
Mounting....................................................................................... 2-2, 8-3
Multiple
Adjustable Frequency Drives............................................. 2-5, 2-6
Motors................................................................................................ 3-1
N
Navigation Keys.................................................................. 3-3, 5-1, 4-3
Noise Isolation..................................................................... 2-5, 3-2, 8-3
O
Open-loop.................................................................................. 2-12, 5-1
Operation Keys..................................................................................... 4-3
Optional Equipment....................................................... 2-7, 2-12, 3-3
Output
Current............................................................................................... 7-1
Performance (U, V, W).............................................................. 10-12
Signal.................................................................................................. 5-4
Terminals................................................................................... 2-3, 3-1
Overcurrent........................................................................................... 7-1
Overload Protection.................................................................. 2-1, 2-5
Overvoltage.................................................................................. 3-6, 7-1
P
PELV................................................................................................. 2-8, 6-4
Power
Connections..................................................................................... 2-5
Factor......................................................................... 1-4, 2-6, 3-2, 8-3
Power-dependent............................................................................ 10-1
Pre-start.................................................................................................. 3-1
Index
VLT
®
AQUA Drive
Instruction Manual
12-2 MG20M922 - VLT
®
is a registered Danfoss trademark