5.5.1 Quick Menu Structure
Q2 Quick Set-up 0-37 Display Text 1 20-12 Reference/Feedback Unit Trending Comparison 29-13 Derag Speed [RPM]
0-01 Language 0-38 Display Text 2 3-02 Minimum Reference Q7 Water and Pumps 29-14 Derag Speed [Hz]
0-02 Motor Speed Unit 0-39 Display Text 3 3-03 Maximum Reference
Q7-1 Pipe Fill
29-15 Derag Off Delay
1-20 Motor Power [kW] Q3-12 Analog Output 6-20 Terminal 54 Low Voltage Q7-10 Horizontal Pipes 29-22 Derag Power Factor
1-22 Motor Voltage 6-50 Terminal 42 Output 6-21 Terminal 54 High Voltage 29-00 Pipe Fill Enable 29-23 Derag Power Delay
1-23 Motor Frequency 6-51 Terminal 42 Output Min Scale 6-24 Terminal 54 Low Ref./Feedb.
Value
29-01 Pipe Fill Speed [RPM] 29-24 Low Speed [RPM]
1-24 Motor Current 6-52 Terminal 42 Output Max Scale 6-25 Terminal 54 High Ref./Feedb.
Value
29-02 Pipe Fill Speed [Hz] 29-25 Low Speed [Hz]
1-25 Motor Nominal Speed Q3-13 Relays
Option relays if applicable
6-00 Live Zero Timeout Time 29-03 Pipe Fill Time 29-26 Low Speed Power [kW]
3-41 Ramp 1 Ramp-up Time
Relay 1 ⇒ 5-40 Function Relay
6-01 Live Zero Timeout Function 29-04 Pipe Fill Rate 29-27 Low Speed Power [HP]
3-42 Ramp 1 Ramp-down Time
Relay 2⇒ 5-40 Function Relay
Q3-31 PID Settings 29-05 Filled Setpoint 29-28 High Speed [RPM]
4-11 Motor Speed Low Limit [RPM]
Q3-2 Open-loop Settings
20-81 PID Normal/ Inverse Control 29-05 Filled Setpoint 29-29 High Speed [Hz]
4-13 Motor Speed High Limit [RPM] Q3-20 Digital Reference 20-82 PID Start Speed [RPM] 29-06 No-Flow Disable Timer 29-30 High Speed Power [kW]
1-29 Automatic Motor Adaptation
(AMA)
3-02 Minimum Reference 20-21 Setpoint 1 Q7-11 Vertical Pipes 29-31 High Speed Power [HP]
Q3 Function Set-up
3-03 Maximum Reference 20-93 PID Proportional Gain 29-00 Pipe Fill Enable 29-32 Derag On Ref Bandwidth
Q3-1 General Settings 3-10 Preset Reference 20-94 PID Integral Time 29-04 Pipe Fill Rate Q7-3 Dry Run
Q3-10 Clock Settings
5-13 Terminal 29 Digital Input Q5 Changes Made 29-05 Filled Setpoint 22-21 Low Power Detection
0-70 Date and Time 5-14 Terminal 32 Digital Input
Q5-1 Last 10 Changes
29-06 No-Flow Disable Timer 22-20 Low Power Auto Set-up
0-71 Date Format 5-15 Terminal 33 Digital Input
Q5-2 Since Factory Setting
Q7-12 Mixed Systems 22-27 Dry Pump Delay
0-72 Time Format Q3-21 Analog Reference
Q5-3 Input Assignments
29-00 Pipe Fill Enable 22-26 Dry Pump Function
0-74 DST/Summertime 3-02 Minimum Reference Q6 Loggings 29-01 Pipe Fill Speed [RPM] Q7-4 End of Curve Detection
0-76 DST/Summertime Start 3-03 Maximum Reference Reference [Unit] 29-02 Pipe Fill Speed [Hz] 22-50 End of Curve Function
0-77 DST_Summertime End 6-10 Terminal 53 Low Voltage Analog Input 53 29-03 Pipe Fill Time 22-51 End of Curve Delay
Q3-11 Display Settings 6-11 Terminal 53 High Voltage Motor current 29-05 Filled Setpoint Q7-5 Sleep Mode
0-20 Display Line 1.1 Small 6-14 Terminal 53 Low Ref./Feedb.
Value
Frequency 29-06 No-Flow Disable Timer
Q7-50 Low Speed
0-21 Display Line 1.2 Small 6-15 Terminal 53 High Ref./Feedb.
Value
Feedback [Unit] Q7-2 Deragging 22-22 Low Speed Detection
0-22 Display Line 1.3 Small
Q3-3 Closed-loop Settings
Energy Log 29-10 Derag Cycles 22-23 No-Flow Function
0-23 Display Line 2 Large Q3-30 Feedback Settings Trending Cont Bin 29-11 Derag at Start/Stop 22-24 No-Flow Delay
0-24 Display Line 3 Large 1-00 Configuration Mode Trending Timed Bin 29-12 Deragging Run Time 22-28 No-Flow Low Speed [RPM]
Table 5.2 Quick Menu Structure
About Adjustable Frequency ...
VLT
®
AQUA Drive
Instruction Manual
MG20M922 - VLT
®
is a registered Danfoss trademark 5-5
5
5
To Next Page
Loading...
Need help?
General