Danfoss VLT Flow Drive FC 111 User Manual

Table 10: Parameter List
5-35 Off Delay, Digital Output
5-4* Relays
5-40 Function Relay
5-41 On Delay, Relay
5-42 Off Delay, Relay
5-5* Pulse Input
5-50 Term. 29 Low Frequency
5-51 Term. 29 High Frequency
5-52 Term. 29 Low Ref./Feedb.
Value
5-53 Term. 29 High Ref./
Feedb. Value
5-8* I/O Options
5-80 AHF Cap Reconnect De-
lay
5-9* Bus Controlled
5-90 Digital & Relay Bus Con-
trol
6-** Analog In/Out
6-0* Analog I/O Mode
6-00 Live Zero Timeout Time
6-01 Live Zero Timeout Func-
tion
6-02 Fire Mode Live Zero
Timeout Function
6-1* Analog Input 53
6-10 Terminal 53 Low Voltage
6-11 Terminal 53 High Volt-
age
6-12 Terminal 53 Low Current
6-13 Terminal 53 High Current
6-14 Terminal 53 Low Ref./
Feedb. Value
6-15 Terminal 53 High Ref./
Feedb. Value
6-16 Terminal 53 Filter Time
Constant
6-19 Terminal 53 mode
6-2* Analog Input 54
6-20 Terminal 54 Low Voltage
6-21 Terminal 54 High Volt-
age
6-22 Terminal 54 Low Current
6-23 Terminal 54 High Current
6-24 Terminal 54 Low Ref./
Feedb. Value
6-25 Terminal 54 High Ref./
Feedb. Value
6-26 Terminal 54 Filter Time
Constant
6-29 Terminal 54 mode
6-7* Analog/Digital Output 45
6-70 Terminal 45 Mode
6-71 Terminal 45 Analog Out-
put
6-72 Terminal 45 Digital Out-
put
6-73 Terminal 45 Output Min
Scale
6-74 Terminal 45 Output Max
Scale
6-76 Terminal 45 Output Bus
Control
6-9* Analog/Digital Output 42
6-90 Terminal 42 Mode
6-91 Terminal 42 Analog Out-
put
6-92 Terminal 42 Digital Out-
put
6-93 Terminal 42 Output Min
Scale
6-94 Terminal 42 Output Max
Scale
6-96 Terminal 42 Output Bus
Control
6-98 Drive Type
8-** Comm. and Options
8-0* General Settings
8-01 Control Site
8-02 Control Source
8-03 Control Timeout Time
8-04 Control Timeout Func-
tion
8-3* FC Port Settings
8-30 Protocol
8-31 Address
8-32 Baud Rate
8-33 Parity/Stop Bits
8-35 Minimum Response De-
lay
8-36 Maximum Response De-
lay
8-37 Maximum Inter-char de-
lay
8-4* FC MC protocol set
8-42 PCD Write Configuration
8-43 PCD Read Configuration
8-5* Digital/Bus
8-50 Coasting Select
8-51 Quick Stop Select
8-52 DC Brake Select
8-53 Start Select
8-54 Reversing Select
8-55 Set-up Select
8-56 Preset Reference Select
8-7* BACnet
8-70 BACnet Device Instance
8-72 MS/TP Max Masters
8-73 MS/TP Max Info Frames
8-74 "I am" Service
8-75 Intialisation Password
8-79 Protocol Firmware ver-
sion
8-8* FC Port Diagnostics
8-80 Bus Message Count
8-81 Bus Error Count
8-82 Slave Messages Rcvd
8-83 Slave Error Count
8-84 Slave Messages Sent
8-85 Slave Timeout Errors
8-88 Reset FC port Diagnos-
tics
8-9* Bus Feedback
8-94 Bus Feedback 1
8-95 Bus Feedback 2
13-** Smart Logic
13-0* SLC Settings
13-00 SL Controller Mode
13-01 Start Event
13-02 Stop Event
13-03 Reset SLC
13-1* Comparators
13-10 Comparator Operand
13-11 Comparator Operator
13-12 Comparator Value
13-2* Timers
13-20 SL Controller Timer
13-4* Logic Rules
13-40 Logic Rule Boolean 1
13-41 Logic Rule Operator 1
13-42 Logic Rule Boolean 2
13-43 Logic Rule Operator 2
13-44 Logic Rule Boolean 3
13-5* States
13-51 SL Controller Event
13-52 SL Controller Action
14-** Special Functions
14-0* Inverter Switching
14-01 Switching Frequency
14-03 Overmodulation
14-07 Dead Time Compensa-
tion Level
14-08 Damping Gain Factor
14-09 Dead Time Bias Current
Level
14-1* Mains Failure
14-10 Mains Failure
14-11 Mains Fault Voltage
Level
14-12 Response to Mains Im-
balance
14-15 Kin. Back-up Trip Recov-
ery Level
14-2* Reset Functions
14-20 Reset Mode
14-21 Automatic Restart Time
14-22 Operation Mode
14-23 Typecode Setting
14-27 Action At Inverter Fault
14-28 Production Settings
14-29 Service Code
14-3* Current Limit Ctrl.
14-30 Current Lim Ctrl, Pro-
portional Gain
14-31 Current Lim Ctrl, Inte-
gration Time
14-32 Current Lim Ctrl, Filter
Time
14-4* Energy Optimising
14-40 VT Level
14-41 AEO Minimum Magnet-
isation
14-44 d-axis current optimiza-
tion for IPM
14-5* Environment
14-50 RFI Filter
14-51 DC-Link Voltage Com-
pensation
14-52 Fan Control
14-53 Fan Monitor
14-55 Output Filter
14-6* Auto Derate
14-61 Function at Inverter
Overload
14-63 Min Switch Frequency
14-64 Dead Time Compensa-
tion Zero Current Level
14-65 Speed Derate Dead
Time Compensation
14-9* Fault Settings
14-90 Fault Level
15-** Drive Information
15-0* Operating Data
15-00 Operating hours
15-01 Running Hours
15-02 kWh Counter
15-03 Power Up's
15-04 Over Temp's
15-05 Over Volt's
AU363928304090en-000101 / 130R098230 | Danfoss A/S © 2021.07
Parameters
VLT® Flow Drive FC 111
Programming Guide

Danfoss VLT Flow Drive FC 111 Specifications

General

Brand	Danfoss
Model	VLT Flow Drive FC 111
Category	DC Drives
Language	English