Danfoss VLT Flow Drive FC 111 User Manual

Table 12: Parameter List
24-06 Fire Mode Reference
Source
24-07 Fire Mode Feedback
Source
24-08 Mul FM Preset Refer-
ence
24-09 FM Alarm Handling
24-1* Drive Bypass
24-10 Drive Bypass Function
24-11 Drive Bypass Delay
Time
25-** Cascade Controller
25-0* System Settings
25-00 Cascade Controller
25-04 Pump Cycling
25-05 Fixed Lead Pump
25-06 Number of Pumps
25-2* Bandwidth Settings
25-20 Staging Bandwidth
25-21 Override Bandwidth
25-22 Fixed Speed Bandwidth
25-23 SBW Staging Delay
25-24 SBW Destaging Delay
25-25 OBW Time
25-27 Stage Function
25-28 Stage Function Time
25-29 Destage Function
25-30 Destage Function Time
25-4* Staging Settings
25-42 Staging Threshold
25-43 Destaging Threshold
25-45 Staging Speed [Hz]
25-47 Destaging Speed [Hz]
25-5* Alternation Settings
25-50 Lead Pump Alternation
25-51 Alternation Event
25-52 Alternation Time Inter-
val
25-53 Alternation Timer Value
25-55 Alternate if Load <=
50%
25-56 Staging Mode at Alter-
nation
25-57 Relays per Pump
25-58 Run Next Pump Delay
25-59 Run on Mains Delay
25-8* Status
25-80 Cascade Status
25-81 Pump Status
25-82 Lead Pump
25-84 Pump ON Time
25-9* Service
25-90 Pump Interlock
30-** Special Features
30-2* Adv. Start Adjust
30-22 Locked Rotor Protec-
tion
30-23 Locked Rotor Detection
Time [s]
30-5* Unit Configuration
30-58 LockPassword
4.2 Parameter Group 0-** Operation / Display
Parameters related to the fundamental functions of the drive, function of the LCP buttons and configuration of the LCP display.
4.2.1 0-0* Basic Settings
Parameter group for basic drive settings.
0-01 Language
Default value: [0] English
Parameter type: Option
2-setup: 1 setup
Conversion index: -
Data type: u_int8
Change during operation: True
Select the language to be used in the display.
Table 13: Option:
[0]
English
[10]
Chinese
0-03 Regional Settings
Default value: [0] International
Parameter type: Option
2-setup: 1 setup
Conversion index: -
Data type: u_int8
Change during operation: False
To meet the needs for different default settings in different parts of the world, parameter 0-03 Regional Settings is implemented in
the drive. The selected setting influences the default setting of the motor nominal frequency.
Table 14: Option:
[0]
International
Set the default value of parameter 1-23 Motor Frequency to 50 Hz.
[1]
North America
Set the default value of parameter 1-23 Motor Frequency to 60 Hz.
0-04 Operating State at Power-up
Default value: [0] Resume
Parameter type: Option
2-setup: All setups
Conversion index: -
Data type: u_int8
Change during operation: True
Select the operating mode after reconnection of the drive to mains voltage after power-down when operating in Hand (local)
mode.
AU363928304090en-000101 / 130R098232 | Danfoss A/S © 2021.07
Parameters
VLT® Flow Drive FC 111
Programming Guide

Danfoss VLT Flow Drive FC 111 Specifications

General

Brand	Danfoss
Model	VLT Flow Drive FC 111
Category	DC Drives
Language	English