9-23 Parameters for Signals
Array [1000]
Read only
Option: Function:
[1655] Feedback 2 [Unit]
[1656] Feedback 3 [Unit]
[1660] Digital Input
[1661] Terminal 53 Switch Setting
[1662] Analog Input 53
[1663] Terminal 54 Switch Setting
[1664] Analog Input 54
[1665] Analog Output 42 [mA]
[1666] Digital Output [bin]
[1667] Pulse Input #29 [Hz]
[1668] Pulse Input #33 [Hz]
[1669] Pulse Output #27 [Hz]
[1670] Pulse Output #29 [Hz]
[1671] Relay Output [bin]
[1672] Counter A
[1673] Counter B
[1675] Analog In X30/11
[1676] Analog In X30/12
[1677] Analog Out X30/8 [mA]
[1680] Fieldbus CTW 1
[1682] Fieldbus REF 1
[1684] Comm. Option STW
[1685] FC Port CTW 1
[1690] Alarm Word
[1691] Alarm Word 2
[1692] Warning Word
[1693] Warning Word 2
[1694] Ext. Status Word
[1695] Ext. Status Word 2
[1696] Maintenance Word
[1840] Analog Input X49/1
[1841] Analog Input X49/3
[1842] Analog Input X49/5
[1843] Analog Out X49/7
[1844] Analog Out X49/9
[1845] Analog Out X49/11
[1846] X49 Digital Output [bin]
[2013] Minimum Reference/Feedb.
[2014] Maximum Reference/Feedb.
[2021] Setpoint 1
[2022] Setpoint 2
[2023] Setpoint 3
[3644] Terminal X49/7 Bus Control
[3654] Terminal X49/9 Bus Control
[3664] Terminal X49/11 Bus Control
9-27 Parameter Edit
Option: Function:
Parameters can be edited via PROFINET, the
standard RS-485 interface, or the LCP.
[0] Disabled Disables editing via PROFINET.
[1] Enabled Enables editing via PROFINET.
9-28 Process Control
Option: Function:
Process control (setting of Control Word, speed
reference, and process data) is possible via either
PROFINET or standard fieldbus but not both
simultaneously. Local control is always possible via
the LCP. Control via process control is possible via
either terminals or fieldbus depending on the
settings in parameter 8-50 Coasting Select to
8-56 Preset Reference Select.
[0] Disable Disables process control via PROFINET, and enables
process control via standard fieldbus or PROFINET
IO-Supervisor.
[1] Enable
cyclic
master
Enables process control via IO Controller, and
disables process control via standard fieldbus or
PROFINET IO-Supervisor..
9-53 Profibus Warning Word
Range: Function:
0 * [0 - 65535 ] This parameter displays PROFINET communi-
cation warnings.
Read only
Bit Condition when bit is active
0 Connection with IO Controller is not ok
1 Reserved for status of connection with second IO
Controller
2 Not used
3 Clear data command received
4 Actual value is not updated
5 No Link on both port
6 Not used
7 Initializing of PROFINET is not ok
8 Drive is tripped
9 Internal CAN error
10 Wrong configuration data from IO Controller
11 Not used
12 Internal error occurred
13 Not configured
14 Timeout active
15 Warning 34 active
Table 8.1 PROFINET Communication Warnings
Parameters
Operating Instructions
48 Danfoss A/S © Rev. 2014-02-27 All rights reserved. MG90U302
88
To Next Page
Loading...
