Datakom D-300 MK2 - Connection Diagrams; AMF Functionality with CTs at Load Side

139 pages

Save Page as PDF

To Next Page

To Previous Page

D-300 MK2 User Manual Firmware V-6.3

L052D01-EN - 38 -

6. CONNECTION DIAGRAMS

6.1. AMF FUNCTIONALITY, CTs AT LOAD SIDE

Main Page

Table of Contents6
Installation Instructions10
Mounting11
Dimensions11
Sealing, Gasket14
Electrical Installation15
Terminal Descriptions16
Battery Voltage Input16
Ac Voltage Inputs17
Ac Current Inputs18
Digital Inputs21
Analog Sender Inputs and Sender Ground21
Charge Input Terminal22
Magnetic Pickup Input22
Mains Contactor Output23
Generator Contactor Output23
Digital Outputs23
Input/Output Extension24
Port (Plug-In Module)25
J1939-Canbus Port26
Usb Device Port26
Gsm Modem (Plug-In Module)27
Ethernet Port (Plug-In Module)28
Wi-Fi (Plug-In Module)29
Topologies30
Selecting the Topology30
Phase, 4 Wire, Star31
Phase, 3 Wire, Delta31
Phase, 4 Wire, Delta32
Phase, 3 Wire, Delta, 2 Ct (L1-L2)32
Phase, 3 Wire, Delta, 2 Ct (L1-L3)33
PHASE, 3 WIRE, DELTA, 2 Cts (L1-L2)33
PHASE, 3 WIRE, DELTA, 2 Cts (L1-L3)34
Phase, 2 Wire34
Functionalities35
Ct Location Selection35
Amf Functionality35
Ats Functionality35
Remote Start Functionality35
Engine Controller Functionality36
Remote Display Unit Functionality37
400Hz Operation37
Connection Diagrams38
AMF FUNCTIONALITY, Cts at LOAD SIDE38
AMF FUNCTIONALITY, Cts at ALTERNATOR SIDE39
Ats Functionality40
Remote Start Functionality41
Engine Control Functionality42
Remote Display Panel Functionality43
Terminal Description44
Technical Specifications47
Description of Controls48
Front Panel Functionality48
Pushbutton Functions49
Display Screen Organization50
Automatic Display Scroll51
Measured Parameters52
Led Lamps53
Waveform Display & Harmonic Analysis54
Displaying Event Logs56
Statistical Counters58
Fuel Filling Counter58
Fuel Consumption Monitoring59
Operation of the Unit60
Quick Start Guide60
Stop Mode60
Auto Mode61
Run Mode, Manual Control62
Test Mode62
Protections and Alarms63
Disabling All Protections64
Service Request Alarm64
Shutdown Alarms65
Loaddump Alarms66
Warnings67
Non-Visual Warnings69
Programming70
Resetting to Factory Defaults70
Entering the Programming Mode71
Navigating between Menus72
Modifying Parameter Value73
Programming Mode Exit74
Program Parameter List75
Controller Configuration Group75
Electrical Parameters Group80
Engine Parameters Group87
Adjust Date and Time94
Weekly Operation Schedule94
Exerciser Schedule95
Sender Configuration96
Digital Input Configuration98
Output Configuration100
Site ID String102
Engine Serial Number102
Modem1-2/Sms1-2-3-4 Telephone Numbers102
Gsm Modem Parameters103
Tcp/Ip Parameters104
Wi-Fi PARAMETERS105
Ethernet Configuration106
Wi-Fi CONFIGURATION107
Gsm Configuration108
Crank Cutting109
Overcurrent Protection (Idmt)110
Motorized Circuit Breaker Control112
J1939 Canbus Engine Support114
Sms Commands118
Software Features120
Load Shedding / Dummy Load120
Load Add / Substract121
Five Step Load Management122
Remote Start Operation123
Disable Auto Start, Simulate Mains123
Battery Charging Operation, Delayed Simulate Mains124
Dual Genset Mutual Standby Operation125
Multiple Voltage and Frequency126
Single Phase Operation126
External Control of the Unit126
Automatic Exerciser127
Weekly Operation Scheduler127
Engine Heating Operation128
Engine Idle Speed Operati̇on128
Engine Block Heater128
Fuel Pump Control129
Gas Engine Fuel Solenoid Control129
Pre-Transfer Signal129
Charging the Engine Battery130
Externally Controlled Digital Outputs130
Combat Mode130
Resetting the Controller131
Automatic Connection Topology Determination131
Zero Power at Rest132
Modbus Communications133
Parameters Required for Rs-485 Modbus Operation134
Data Formats134
Declaration of Conformity137
Maintenance137
Disposal of the Unit137
Rohs Compliance137
Troubleshooting Guide138

Datakom D-300 MK2 - Connection Diagrams; AMF Functionality with CTs at Load Side

Table of Contents

Related product manuals