SAFETY RULES
Woodworking can be dangerous ifsafe and proper operating procedures are not followed. As with all machinery, there are certain
hazards involved with the operation of the product. Using the machine with respect and caution will considerably lessen the
possiblity of personal injury. However, ifnormal safety precautions are overlooked or ignored, personal injuryto the operator may
result. Safety equipment such as guards, push sticks, hold-downs, featherboards, goggles, dust masks and hearing protection
can reduce your potential for injury. But even the best guard won't make up for poor judgment, carelessness or inattention.
use common sen_ and exercise caution inthe workshop. Ifa procedure feels dangerous, don't try it. Figure out an alternative
procedure that feels safer. REMEMBER: Your personal safety is your responsibility.
This machine was designed for certain applications only. Delta Machinery strongly recommends that this machine not be modified
and/or used for any application other than that for which it was designed. If you have any questions relative to a particular
application, DO NOT use the machine until you have first contacted Delta to determine ifit can or should be performed on the
product.
DELTA iNTERNATIONAL MACHINERY CORP.
MANAGER OF TECHNICAL SERVICES
246 ALPHA DRIVE
PmTTSBURGH, PENNSYLVANIA 15238
(iN CANADA: 644 iMPERIAL ROAD, GUELPH, ONTARIO N1H 6M7)
WARNING: FAILURE TO FOLLOW THESE RULES
MAY RESULT iN SERIOUS PERSONAL iNJURY
1. FOR YOUR OWN SAFETY, READ iNSTRUCTiON
MANUAL BEFORE OPERATING THE TOOL. Learn the
tool's application and limitations as well as the specific hazards
peculiar to it.
2. KEEP GUARDS iN PLACE and in working order.
3. ALWAYS WEAR EYE PROTECTION.
4. GROUND ALL TOOLS. If tool is equipped with three-
prong plug, it should be plugged into a three-hole electrical
receptacle, ifanadapter is used to accommodate a two-prong
receptacle, the adapter lug must be attached to a known
ground. Never remove the third prong.
5. REMOVE ADJUSTING KEYS AND WRENCHES. Form
habit of checking to see that keys and adjusting wrenches are
removed from tool before turning it "on."
6. KEEP WORK AREA CLEAN. Cluttered areas and
benches invite accidents.
7. DON'T USE iN DANGEROUS ENVIRONMENT. Don't
use power toolsin damp or wet locations, or expose them to
rain. Keep work area well-lighted.
8. KEEP CHILDREN AND VISITORS AWAY. All children
and visitors should be kept a safe distance from work area.
9. MAKE WORKSHOP CHILDPROOF - with padlocks,
master switches, or by removing starter keys.
10. DON'TFORCETOOL. Itwiltdothejobbetterandbesafer
at the rate for which it was designed.
11. USE RIGHT TOOL. Don't force tool or attachment to do
a job for which itwas not designed.
12. WEAR PROPER APPAREL. No loose clothing, gloves,
neckties, rings, bracelets, or other jewelry to get caught in
moving parts. Nonslip footwear is recommended. Wear
protective hair covering to contain long hair.
13. ALWAYS USE SAFETY GLASSES. Wear safety glasses
(must comply with ANSI Z87.1). Everyday eyeglasses only
have impactresistant lenses; they are not safety glasses. Also
use face or dust mask ifcutting operation is dusty.
14. SECURE WORK. Use clamps or a vise to hold work when
practical. It'ssafer than using your hand and frees both hands
to operate tool.
15. DON'T OVERREACH. Keep proper footing and balance
at all times.
16. MAiNTAiN TOOLS IN TOP CONDiTiON. Keep tools
sharp and clean for best and safest performance. Fellow
instructions for lubricating and changing accessories.
17. DISCONNECT TOOLS before servicing and when
changing accessories such as blades, bits, cutters, etc.
18. USE RECOMMENDED ACCESSOR|ES. The use of
improperaccessories may cause hazards or risk of injury to
persons.
19. REDUCE THE RaSK OF UNiNTENTiONAL START-
iNG, Make sure switch is in"OFF" position before plugging in
power cord.
20. NEVER STAND ON TOOL. Serious injury could occur if
the tool istipped or ifthe cutting tool isaccidentally contacted.
21. CHECK DAMAGED PARTS. Before further use of the
tool, a guard or other part that isdamaged should be carefully
checked to ensure that itwill operate properly and perform its
intended function - check for alignment of moving parts,
binding of moving parts, breakage of parts, mounting, and any
other conditions that may affect itsoperation= A guard or other
part that is damaged should be properly repaired or replaced.
22. DiRECTiON OF FEED. Feed work into a blade or cuttter
against the direction of rotation of the blade or cutter only.
23. NEVER LEAVETOOL RUNN|NG UNATTENDED. TURN
POWER OFF. Don't leave tool until it comes to a complete
stop.
24. DRUGS, ALCOHOL, MEDiCATiON. Do not operate tool
while under the influenceof drugs, alcohol or any medication.
25. MAKE SURETOOL IS D|SCONNECTED FROM POWER
SUPPLY while motor is being mounted, connected or
reconnected.
26. WARNING: The dust generated by certain woods and
wood products can be injurious to your health. Always operate
machinery in welt ventilated areas and provide for proper dust
removal. Use wood dustcollection systems whenever possible.
To Next Page
Loading...
Need help?
General
