S
Samantha ByrdSep 9, 2025
Why are HDMI audio signals not output from speakers on my Denon Stereo Receiver?
- MMiguel ShahSep 9, 2025
If the “Manual Setup” – “HDMI Setup” – “HDMI Audio Out” setting is set to “TV”, change it to “AMP”.
To Next PageTo Next Page
Why are HDMI audio signals not output from speakers on my Denon Stereo Receiver?
If the “Manual Setup” – “HDMI Setup” – “HDMI Audio Out” setting is set to “TV”, change it to “AMP”.
How do I get DTS sound to output on my Denon AVR-590 Stereo Receiver?
Verify that the Blu-ray Disc player / DVD player’s audio output setting is set to bitstream. Ensure your player is compatible with DTS sound playback. On the AVR-590, set the “Decode Mode” to “Auto” or “DTS” mode, not “PCM”.
Why is there no sound coming from my Denon Stereo Receiver speakers?
Several factors could be at play. First, check that all connections to the input devices and speaker cables are secure. Ensure the input source selected on your Denon Stereo Receiver matches the device you're trying to play. Also, verify that the master volume isn't set too low and that mute mode is off. Disconnect any connected headphones, and if you're using digital inputs, confirm that the correct input source is selected and the input mode is properly configured.
Why is there no picture appearing on my Denon AVR-590 Stereo Receiver?
Check the connections between the AVR-590 and the monitor to ensure they are secure. Verify that the monitor's input setting is correct. If using component input connectors with video output connectors, set the player to interlace (480i/576i) signals, as high-definition signals are not down-converted.
How to fix a Denon Stereo Receiver when it does not operate properly?
External noise or interference may be causing the set to malfunction. Try resetting the microprocessor.
Why doesn't my Denon Stereo Receiver remote control work properly?
Several reasons may cause the remote control to malfunction. First, replace the batteries with new ones. Ensure you are operating within the specified range and that there are no obstacles between the remote and the main unit. Check that the batteries are inserted correctly, following the polarity marks. Move the set away from strong light sources that might interfere with the remote control sensor. Also, make sure the device selection switch and device mode are properly set for the device you are trying to operate.
Why won't my Denon Stereo Receiver turn on, or why does it turn off immediately?
This might be due to a faulty power cord connection. Check the insertion of the power cord plug to ensure it is properly connected.
What to do if my Denon AVR-590 Stereo Receiver power switches off suddenly and the power indicator flashes in red?
The protection circuit may be activated due to a temperature rise in the internal parts. Immediately switch off the power and allow the unit to cool down sufficiently before reapplying power. Also, ensure the AVR-590 is installed in a well-ventilated area.
What to do if my Denon AVR-590 Stereo Receiver power switches off suddenly and the power indicator flashes red?
If the power indicator flashes red at intervals of approximately 0.5 seconds, it could be due to using speakers with impedance lower than specified. Please use speakers with the correct impedance. Alternatively, check for speaker cable core wires touching each other or the AVR-590 rear panel. If this is the case, unplug the power cord, twist the core wires together tightly, and reconnect.
Why does my Denon Stereo Receiver have no sound?
Several factors could cause a lack of sound from your Denon Stereo Receiver speakers. First, check the connections to your input devices and speaker cables to ensure they are secure. Then, verify that the input source selected on the receiver matches the device you're trying to play. Also, make sure the master volume isn't set too low and that mute mode is off. Disconnect any connected headphones, as they may be diverting the audio. If using digital inputs, confirm that digital signals are being input and that the input mode is correctly set.
General| Channels | 5.1 |
|---|---|
| Power Output | 75 W per channel (8 ohms, 20Hz-20kHz, 0.08% THD) |
| HDMI Inputs | 4 |
| HDMI Outputs | 1 |
| Signal-To-Noise Ratio | 98 dB |
| THD | 0.08% |
| Input Impedance | 47 kOhm |
| Input Sensitivity | 200 mV |
| Surround System Class | 5.1 channel |
| HDMI Switching | Yes |
| 3D Technology | Yes |
| Input Sensitivity/Impedance | 200 mV / 47 kOhm |
| HDMI Version | 1.3a |
| Dolby Formats | Dolby Digital, Dolby Digital Plus |
| DTS Formats | DTS, DTS Neo:6, DTS 96/24 |
| Audyssey | MultEQ |
| Amplifier Output Details | 75 W per channel at 8 ohms, 20 Hz to 20 kHz, 0.08% THD |
| Response Bandwidth | 10Hz - 100kHz |
| Audio D/A Converter | 192 kHz/24-bit |
| Frequency Response | 10 Hz to 100 kHz |
| Video Inputs/Outputs | Composite, Component |
| Audio Inputs/Outputs | Digital Optical |
