EasyManuals Logo

Denon AVR-2309 User Manual

Denon AVR-2309
81 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #59 background imageLoading...
Page #59 background image
Last Function Memory
This stores the settings as they were directly before the standby
mode was set.
When the power is turned back on, the settings are restored to as
they were directly before the standby mode was set.
Backup Memory
The various settings are backed up for about 1 week, even if the
power is turned off or the power cord is disconnected.
Resetting the Microprocessor
Perform this procedure if the display is abnormal or if operations
cannot be performed.
When the microprocessor is reset, all the settings are reset to
their default values.
1
Turn off the power using <POWER>.
2
Press <POWER> while simultaneously pressing
<INPUT MODE> and <SPEAKERS>.
3
Once the display starts ashing at intervals of about 1
second, release the two buttons.
If in step 3 the display does not flash at intervals of about 1 second,
start over from step 1.
Quick Select Function
With this function, the currently playing input source, input mode,
surround mode, MultEQ settings and volume can be stored in the
memory.
1
Set the input source, surround mode, MultEQ,
Dynamic EQ, Dynamic Volume, Front Speaker
settings and volume to the conditions you want to
store.
2
Press and hold the desired QUICK SELECT until
“Memory” appears on the display.
The current settings will be memorized.
To call out the settings, press QUICK SELECT at which the desired
settings were stored.
The Quick Select name can be changed (vpage 31).
NOTE
Input sources stored with the quick select function cannot be selected
if they have been deleted at menu “Manual Setup” “Option Setup”
“Source Delete” (vpage 30). In this case, store them again.
Input Source Volume
Quick Select 1 DVD –40 dB
Quick Select 2 TV/CBL –40 dB
Quick Select 3 VCR –40 dB
[Quick Select Defaults]
Personal Memory Plus Function
This function sets the settings (input mode, surround mode, HDMI
output mode, MultEQ, Dynamic EQ, Dynamic Volume, audio delay
etc.) last selected for the individual input sources.
When you switch to an input source, the settings are automatically
set to the ones that were set the last time that input source was
used.
The surround parameters, tone settings and the volumes of the
different speakers are stored for the individual surround modes.

Getting Started Connections Setup Playback Remote Control Multi-zone Information Troubleshooting
ENGLISH
Specifications

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Denon AVR-2309 and is the answer not in the manual?

Denon AVR-2309 Specifications

General IconGeneral
Number of Channels7.1
HDMI Inputs4
HDMI Outputs1
Dolby TechnologiesDolby Digital, Dolby Digital Plus, Dolby TrueHD, Dolby Pro Logic IIx
Auto CalibrationAudyssey MultEQ
Component Video Inputs3
Analog Audio Inputs7
Response Bandwidth10 - 100000 Hz
Signal-To-Noise Ratio100 dB
THD0.08%
Input Impedance47 kOhm
Input Sensitivity200 mV
Tuner Presets56
HDMI SwitchingYes
Surround Sound EffectsYes
Digital Sound Processor (DSP)Yes
DSP Preset Qty7
HDMI Pass-ThroughYes
Frequency Response10 - 100000 Hz
DTS TechnologiesDTS-HD Master Audio
Digital Audio Inputs2 Coaxial
Audio D/A Converter192kHz/24-bit
Amplifier Output Details100 Watt - 8 Ohm - 20 - 20000 Hz - THD 0.08% - 7 channel(s)

Related product manuals