9
ENGLISH
Remote control unit
• For details on the functions of these parts, refer to the pages given in parentheses ( ).
SYSTEM CALL buttons................(22)
ON SCREEN/DISPLAY button
..(29, 39)
Cursor buttons
................(10~18, 20~25, 31~37, 42)
TEST TONE button ......................(31)
System buttons ...............(19, 21, 22)
ZONE 2 buttons ...........................(30)
BACKLIGHT button
Input source selector
buttons....(19, 21, 26, 33, 35, 39~41)
SYSTEM SETUP/SETUP
button ..............................(10, 18, 35)
Mode selector
buttons ................(19, 20, 22, 26, 30)
Surround buttons
..................................(27, 28, 32~36)
ZONE 1/MAIN buttons.................(30)
Power button.........................(20~26)
Tuner system/System
button ........................(21, 30, 39~41)
MUTING button ...........................(28)
Master volume control
buttons...................................(27, 30)
RDS/RETURN button.......(21, 40~42)
Remote control signal
transmitter ...................................(19)
7
SETTING UP THE SYSTEM
• Once all connections with other AV components have been completed as described in “CONNECTIONS”
(see pages 4 to 8), make the various settings described below on the monitor screen using the AVR-3803’s
on-screen display function.
These settings are required to set up the listening room’s AV system centered around the AVR-3803.
• Use the following buttons to set up the system:
• Check that the remote control unit is set to AMP mode.
SYSTEM SETUP button
Press this to display the system setup menu.
ENTER button
Press this to switch the display.
Also use this button to complete the setting.
CURSOR buttons
0
and
1
: Use these to move the cursors (
0
and
1
) to
the left and right on the screen.
• and ª: Use these to move the cursors (• and ª) to
the up and down on the screen.
• System setup items and default values (set upon shipment from the factory)
INPUT MODE selector
buttons.......................(26, 27, 33, 35)
SURROUND PARAMETER
button ........................(32~34, 36, 37)
CH SELECT/ENTER button
.........(10~18, 20~25, 31~33, 35, 37)
SURROUND SPEAKER/
SURROUND BACK buttons...(29, 34)
System setup Default settings
y
e
r
Speaker
Configuration
Surround
Speaker Setting
Subwoofer
mode
Dolby Digital
Setup
Channel Level
Digital In
Assignment
Input the combination of speakers in your system and their
corresponding sizes (Small for regular speakers, Large for full-
size, full-range) to automatically set the composition of the
signals output from the speakers and the frequency response.
Use this function when using multiple surround
speaker combinations for more ideal surround
sound. Once the combinations of surround
speakers to be used for the different surround
modes are preset, the surround speakers are
selected automatically according to the surround
mode.
This selects the subwoofer speaker for playing deep bass
signals.
Turn the audio compression on or off when down-mixing Dolby
Digital signals.
This adjusts the volume of the signals output from the speakers
and subwoofer for the different channels in order to obtain
optimum effects.
This assigns the digital input jacks for the different
input sources.
Surround
mode
Surround
speaker
Input
source
Digital
Inputs
Front Sp.
Large
Center Sp. Surround Sp. A /BSub Woofer
Small SmallYes
DOLBY/
DTS
SURROUND
WIDE SCREEN
5CH/7CH
STEREO
DSP
SIMULATION
EXT. IN
AAAA A
LFE
Front L & R Center Surround L & RSub Woofer
3.6 m (12 ft) 3.6 m (12 ft) 3.0 m (10 ft)3.6 m (12 ft)
Front L
Front R Center
Surround
R
Surround
Back R
Subwoofer
0 dB 0 dB 0 dB 0 dB 0 dB 0 dB
CD DVD VDP TV DBS CDR/TAPE
COAX1 COAX2 OPT1 OPT2 OPT3 OPT5
Surround Back Sp.
Small / 2spkrs
OFF
w
Delay Time
This parameter is for optimizing the timing with which the
audio signals are produced from the speakers and subwoofer
according to the listening position.
SBL & SBR
3.0 m (10 ft)
Surround
Back L
0 dB
Surround
L
0 dB
VCR-1
OPT4
V. AUX
OFF
q
Crossover
Frequency
Set the frequency (Hz) below which the bass sound of the
various speakers is to be output from the subwoofer.
80 Hz
VCR-2
OFF
t
Video Setup
This assigns the color difference (component)
video input jacks for the different input sources.
DVD
VDP TV VCR-1 V. AUX —
VIDEO1 NONE NONE NONE NONE —
VCR-2
NONE
DBS
VIDEO2
Set the input signal to be output from the
monitor output terminal.
AUTO
Component
In Assign
Video Input
Mode
Set this to switch the surround back channel’s
power amplifier for use for zone 2.
Surround Back
Power AMP
Assignment
This sets the output level for the zone 2 output
jacks.
Variable
Zone2 vol.
Level
u
Zone2 Control
To Next Page
Loading...
Need help?
General
