Denon AVR-X2100W Service Manual

1.10. About the error code
See the table below for error codes and details of faults when the rmware is updated through USB memory.
Error
Code
Details of Error code Display Coping strategies
01
Unable to detect USB.
C o n n e c t i o n F a i l 0 1
Disconnect and connect the USB
memory.
02
No FirmwareFile in USB.
F i l e s N o t F o u n d 0 2
Make sure that the FirmwareFile is in
the USB memory.
03
FirmwareFile in USB for unsup-
ported Model name/area.
N o t M a t c h F i r m 0 3
Check the supported Model name/area
for the FirmwareFile.
04
Failed to obtain individual Firm-
ware information.
C o n n e c t i o n F a i l 0 6
Start the USB Update again.
05
TimeOut while obtaining individual
Firmware information.
C o n n e c t i o n F a i l 0 7
Start the USB Update again.
06
Failed to obtain entire Firmware
information.
C o n n e c t i o n F a i l 0 4
Start the USB Update again.
07
TimeOut while obtaining entire
Firmware information.
C o n n e c t i o n F a i l 0 5
Start the USB Update again.
08
Error notication received while
requesting FirmwareInfo.
C o n n e c t i o n F a i l 0 8
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
09
TimeOut while obtaining Firmware
information.
C o n n e c t i o n F a i l 0 9
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
0A
Unable to detect USB for Firm-
wareDownload.
C o n n e c t i o n F a i l 0 A
Disconnect and connect the USB
memory.
0B
No FirmwareFile for Firmware-
Download.
F i l e s N o t F o u n d 0 B
Disconnect and connect the USB
memory.
0D
Received value with invalid
PackageVersion.
C o n n e c t i o n F a i l 0 D
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
10
No UpdatePacket received from
CX870 (TimeOut).
U p d a t i n g f a i l 1 0
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
11
Abnormal data in UpdatePacket
received from CX870 (FormatEr-
ror).
U p d a t i n g f a i l 1 1
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
12
Abnormal data in UpdatePacket
received from CX870 (CheckSum-
Error).
U p d a t i n g f a i l 1 2
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
63

Denon AVR-X2100W Specifications

General

Receiver type	Surround
Frequency range	10 - 100000 Hz
Audio output channels	7.1 channels
Signal-to-Noise Ratio (SNR)	100 dB
Power output per channel (1KHz@6 Ohm)	150 W
Power output per channel (20-20KHz@8 Ohm)	95 W
HDMI in	8
Composite video in	2
Component video (YPbPr/YCbCr) in	1
Speakers connectivity type	-
Ethernet LAN	Yes
AM band range	522 - 1611 kHz
FM band range	87.5 - 108 MHz
Supported radio bands	AM, FM
Optical drive included	No
Product color	Black
Audio decoders	Dolby Digital EX, Dolby Pro Logic IIx, Dolby TrueHD, DTS 96/24, DTS-ES, DTS-HD
Apple docking compatibility	iPhone, iPod
AC input voltage	230 V
AC input frequency	50 Hz
Power consumption (standby)	0.1 W
Power consumption (typical)	500 W

Weight and Dimensions

Depth	339 mm
Width	434 mm
Height	167 mm
Weight	9700 g