EasyManuals Logo

Denon AVR-X2100W Service Manual

Denon AVR-X2100W
194 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #64 background imageLoading...
Page #64 background image
Error
Code
Details of Error code Display Coping strategies
13
BlockErase failed before rewriting
Main.
E r a s e f a i l 1 3
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
14
BlockWrite failed while rewriting
Main.
U p d a t i n g f a i l 1 4
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
15
Error in Verify after rewriting Main
(CheckSumError).
U p d a t e C h e c k N G 1 5
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
20
Unable to detect USB after
SBLMode.
C o n n e c t i o n F a i l 2 0
Disconnect and connect the USB
memory.
21
No FirmwareFile in USB after
SBLMode.
F i l e s N o t F o u n d 2 1
Disconnect and connect the USB
memory.
22
FirmwareFile in USB after
SBLMode for unsupported Model
name/area.
N o t M a t c h F i r m 2 2
Check the supported Model name/area
for the FirmwareFile.
23
Failed to obtain entire Firmware
information after SBLMode.
C o n n e c t i o n F a i l 2 3
Disconnect and connect the USB
memory.
24
TimeOut while obtaining en-
tire Firmware information after
SBLMode.
C o n n e c t i o n F a i l 2 4
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
25
Failed to transit to SBLMode.
C o n n e c t i o n F a i l 2 5
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
26
TimeOut in Download (writing to
SDRAM) for FirmwareDownload.
D o w n l o a d f a i l 2 6
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
27
Failed to write to EEPROM after
SBLMode.
C o n n e c t i o n F a i l 2 7
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
36
Unable to detect USB.
C o n n e c t i o n F a i l 3 6
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
37
No FirmwareFile in USB.
F i l e s N o t F o u n d 3 7
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
38
FirmwareFile in USB for unsup-
ported Model name/area.
N o t M a t c h F i r m 3 8
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
64

Table of Contents

Other manuals for Denon AVR-X2100W

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Denon AVR-X2100W and is the answer not in the manual?

Denon AVR-X2100W Specifications

General IconGeneral
Receiver typeSurround
Frequency range10 - 100000 Hz
Audio output channels7.1 channels
Signal-to-Noise Ratio (SNR)100 dB
Power output per channel (1KHz@6 Ohm)150 W
Power output per channel (20-20KHz@8 Ohm)95 W
HDMI in8
Composite video in2
Component video (YPbPr/YCbCr) in1
Speakers connectivity type-
Ethernet LANYes
AM band range522 - 1611 kHz
FM band range87.5 - 108 MHz
Supported radio bandsAM, FM
Optical drive includedNo
Product colorBlack
Audio decodersDolby Digital EX, Dolby Pro Logic IIx, Dolby TrueHD, DTS 96/24, DTS-ES, DTS-HD
Apple docking compatibilityiPhone, iPod
AC input voltage230 V
AC input frequency50 Hz
Power consumption (standby)0.1 W
Power consumption (typical)500 W
Weight and Dimensions IconWeight and Dimensions
Depth339 mm
Width434 mm
Height167 mm
Weight9700 g

Related product manuals