Denon AVR-X4100W

Error
Code
USB Update Error Display Details of Error code Coping strategies
5B
S u b * * * m i n
U p d a t i n g f a i l 5 B
NACK received in response or no
response from Sub for L com-
mand.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
5C
S u b * * * m i n
U p d a t i n g f a i l 5 C
No Update Packet received from
CX870 / CY920 (Time Out).
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
5D
S u b * * * m i n
U p d a t i n g f a i l 5 D
Abnormal data in Update Packet
received from CX870 / CY920
(CRCError).
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
5E
S u b * * * m i n
U p d a t i n g f a i l 5 E
Abnormal data in Update Packet
received from CX870 / CY920
(PacketNoError).
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
5F
S u b * * * m i n
U p d a t i n g f a i l 5 F
Setup failure of the transfer meth-
od of XModem.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
60
S u b * * * m i n
U p d a t i n g f a i l 6 0
NACK received in response or no
response from Sub for P com-
mand.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
61
S u b * * * m i n
U p d a t e C h e c k N G 6 1
Mismatched Check Sum in re-
sponse or no response from Sub
for I command.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
62
S u b * * * m i n
U p d a t i n g f a i l 6 2
Failed to start up Sub in Power On
sequence during Update.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
63
S u b * * * m i n
U p d a t i n g f a i l 6 3
Failed to transit to Application
Mode.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
64
S u b * * * m i n
U p d a t i n g f a i l 6 4
Failed to transit to Application
Mode.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
80
G U I * * * m i n
U p d a t i n g f a i l 8 0
Write Enable Latch Bit not set in
Read after issuing WREN com-
mand.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
81
G U I * * * m i n
U p d a t i n g f a i l 8 1
Block Erase failed in Read after
issuing BE command.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
82
G U I * * * m i n
U p d a t i n g f a i l 8 2
No Update Packet received from
CX870 / CY920 (Time Out).
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
83
G U I * * * m i n
U p d a t i n g f a i l 8 3
Abnormal data in Update Packet
received from CX870 / CY920
(CRCError).
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
87