EasyManuals Logo

Denon AVR-X6400H Service Manual

Denon AVR-X6400H
203 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #146 background imageLoading...
Page #146 background image
1.5. Version Display in the Setup Menu
Follow the steps below to display the rmware information.
(1) Press the "
SETUP
" button on the remote control.
(2) Select "General - Information - Firmware".
The version information is displayed as a 16-digit number as shown in the screenshot below.
This 16-digit number comprises a part of the version number of each device and module.
Numerics and version numbers correspond as shown below.
b
The rmware version numbers and this 16-digit version information are written in the Service Information.
b
Replace as follows for the 5th to 7th digits of HEOS version.
X.XXX.X → X.XXX.00X
X.XXX.XX → X.XXX.0XX
X.XXX.XXX → X.XXX.XXX
XXXX-XXXX-XXXX-XXXX
X.XX.XX.XX
General/Firmware
Version
GUI Image
-DTS Version
Main
DSP4
A.PLD
GUI
LEGO Version
X . 3 6 7 . 1 3 X
X X X X X X 1 6
X X X
X X X
X X X X
1 5 3 4X
1
V.PLD
X X X 5
8
DSP3
X X X 6
DSP2
X X X 4
DSP1
X X X 2
XX X 5- 1 4 31
Info display 2 4 6 - 6 5 3 1 - 7 8 6 3
The 1st digit from the right for DSP1
The 1st digit from the right for DSP2
The 1st digit from the right for DSP3
The 1st digit from the right for DSP4
The 1st digit from the right for A.PLD
The 1st digit from the right for V.PLD
The 3rd digit from the right for HEOS
The 2nd digit from the right for HEOS
The 4th digit from the right for HEOS
The 5th digit from the right for HEOS
The 6th digit from the right for HEOS
The 1st digit from the right for GUI
The 6th digit from the right for Main
The 5th digit from the right for Main
The 2nd digit from the right for Main
The 1st digit from the right for Main
146
Caution in
servicing
Electrical Mechanical Repair Information Updating

Table of Contents

Other manuals for Denon AVR-X6400H

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Denon AVR-X6400H and is the answer not in the manual?

Denon AVR-X6400H Specifications

General IconGeneral
Receiver typeSurround
Frequency range10 - 100000 Hz
Pre-out channels11.2
Input sensitivity200 mV
Pre-out connectivityYes
Audio output channels11.2 channels
Signal-to-Noise Ratio (SNR)100 dB
Power output per channel (1KHz@6 Ohm)205 W
Power output per channel (20-20KHz@8 Ohm)140 W
Display-
HDCP version2.2
Apple dockingNo
Product colorSilver
Audio decodersDTS:X, Dolby Atmos
Audio formats supportedALAC, DSD, FLAC, WAV
RS-232 ports1
Connectivity technologyWireless
AM band range522 - 1611 kHz
FM band range87.5 - 108 MHz
Supported radio bandsAM, FM
Internet radio services supportedDeezer, Napster, Spotify, Tidal, TuneIn
HDMI in8
Composite video in4
Component video (YPbPr/YCbCr) in2
AC input voltage230 V
AC input frequency50 Hz
Power consumption (standby)0.5 W
Power consumption (typical)750 W
Number of HDMI outputs3
Weight and Dimensions IconWeight and Dimensions
Depth393 mm
Width434 mm
Height167 mm
Weight14500 g

Related product manuals