Denon DBP-4010UD - Audio Setup Configuration; 7.1 ch Audio Output Settings

TroubleshootingInformationHDMI Control FunctionPlaybackConnectionsGetting Started Speci cations
ENGLISH
2
Setting items
Setting contents
7.1ch Audio Out
GSurr. BackH : Set the presence, size and number of surround back
speakers.
Size : Set the surround back speaker size.
Large : Use of a large speaker that can adequately play back low
frequencies.
Small : Use of a small speaker that has inadequate playback capacity
for low frequencies.
None : Select when the surround back speakers are not connected.
Number : Set the number of surround back speakers.
1 spkr : Use only one surround back speaker. Surround back audio is
output from the surround back L terminal.
2 spkrs : Use two surround back speakers.
GCrossover Freq.H : Set the upper limit of the low frequency signals
output from the subwoofer.
40Hz/60Hz/80Hz/90Hz/100Hz/110Hz/120Hz/150Hz/200Hz/250Hz
: Outputs at below set frequency, each speaker’s bass signal
output from the subwoofer. Set this according to the low frequency
reproduction capabilities of the speakers you are using.
Advanced : Set the low frequency signals to be output from the
signals of the respective speakers to the subwoofer.
Front, Center, Surround, Surr. Back
40Hz/60Hz/80Hz/90Hz/100Hz/110Hz/120Hz/150Hz/200Hz/250Hz
LFE / LFE+Main
80Hz/90Hz/100Hz/110Hz/120Hz/150Hz/200Hz/250Hz
When, on the GUI menu, “Audio Setup” – “7.1ch Audio Out”– “Multi
Channel” – “Speaker Con guration” – “Subwoofer” is set to “Yes”
(vpage 25), you can select “LFE” or “LFE+Main”.
•
•
•
•
Setting items
Setting contents
7.1ch Audio Out
Makes the audio setting for
output of analog 7.1-channel
audio to a multi-channel
ampli er.
To set “7.1ch Audio Out”,
set “HDMI Setup” – “Audio
Setup” on the GUI menu to
“2Ch” or “Mute” (vpage
24).
NOTE
You cannot select “None”
or “No” for “HDMI Setup”
– Audio Setup” – “Multi
LPCM BM On” – “Speaker
Con guration” (vpage 23,
24) on the GUI menu.
Multi Channel
Set the speaker con guration, channel level and distance for multi-
channel playback.
2 Channel
Outputs multi-channel downmixed audio from the front speaker output
terminals (FL/FR) of the 7.1-channel audio output terminals. Make this
setting when outputting to a TV and 2-channel ampli er.
NOTE
The 7.1-channel audio output terminals output only FL/FR when you
make this setting.
n Speaker Con guration : Set the speaker con guration.
GFrontH : Set the front speaker size.
Large : Use of a large speaker that can adequately play back low
frequencies.
Small : Use of a small speaker that has inadequate playback capacity
for low frequencies.
GCenterH : Set the presence and size of the center speaker.
Large : Use of a large speaker that can adequately play back low
frequencies.
Small : Use of a small speaker that has inadequate playback capacity
for low frequencies.
None : Select when a center speaker is not connected.
GSubwooferH : Set the presence of a subwoofer.
Yes : Use a subwoofer.
No : Select when a subwooofer is not connected.
GSurroundH : Set the presence and size of the Surround speakers.
Large : Use of a large speaker that can adequately play back low
frequencies.
Small : Use of a small speaker that has inadequate playback capacity
for low frequencies.
None : Select when the surround speakers are not connected.
•
•
•
•
•
•
•
•
•
•
Set the speaker or audio to be output.
Setting related to each channel setting and other audio in the case of outputting analog
audio signals decoded by the DBP-4010UD.
Audio Setup
Default settings are underlined.
Remote control operation
buttons
:
Displaying the menu
Cancel the menu
:
Moves the cursor
(Up/Down/Left/Right)
:Decision the setting :Return to previous menu
Setup
See overleaf