ENGLISH
1.
Home Theater Playback - Playing Back Using Multi-channel System -
~.
Using
an
HOMI Cable
to
Connect
to
an
AV
Amp or Television
*1 : If the number
of
channels supported by 2 devices
is
the same, multi-channel audio
is
output
to both devices.
Video and Audio Output Signal when Outputting
to
2 HOMI Devices
(HOMI Auto(Oual) Mode and HOMI Auto (Independent) Mode)
Default settings are underlined.
o About Video Signal
When 'About HDMI Video Resolution Setting"
(&page
15)
is
set
to
"Auto",
of
the resolution
supported by both
of
the 2 connected devices, the DVD-A1
UDCI
outputs the highest resolution
video signal to both devices.
o About Audio Signal
(1)
Check audio signals that
can
be
input
by
the device
to
be
connected.
• Audio format ······Bit stream (Dolby Digital.
DTS
etc.), Linear PCM, etc.
• Number of channels
(2) About number of output channels of multi-channel audio
When outputting bitstream signals to
two
HDMI devices, the signals
are
output
to
both HDMI devices
if they both support bitstream signals. Of only one device support bit stream, LPCM
is
output
to
the
device, which does not support bit stream.
When outputting LPCM signals to
two
HDMI devices, it
is
not possible
to
output
multi-channel audio
signals with different numbers of channels
to
the
two
HOMI devices.
When the number of channels
of
multi-channel audio supported by the connected 2 HDMI devices
are different, the audio signal output to each mode becomes
as
follows:
• HOMI Auto (Dual) :
Outputs multi-channel audio of less number of channels to both devices.
If the supported number
of
channels
is
7.1
channel and
5.1
channel, respectively,
5.1
channel audio
is output. If the supported number
of
channels
is
multi-channel and 2-channel (or 2.1-channel). multi-
channel and 2-channel are output.
• HOMI Auto (Independent) :
Multi-channel audio
is
output
as
is
to
the device, which supports more number
of
channels.
LPCM audio
of
2-channel
is
output to the other device.
We recommend you use this mode when outputting to both
an
AV
Amp and TV
o About Audio Format
to
be
Output
Audio format supported by 2 connected HDMI devices
is
output.
When multi-channel audio
is
output, the
output
channel
is
as
described above
(2).
Audio
Video + Audio
Video + Audio
Video
Video + Audio
Video + Audio
HOMlmode
~~
CD
HOMI Auto (Duall
(HOMI Dual)
® HOMI Auto (Independent)
(HOMllnde.)
® AV Pure Direct
(AV P.Oirect)
@HOMI2
® HOMI1
® HOMI Off
• There are 5 ways
to
connect
(CD
- @) using HOMI cable (sold
se
arately). Configure appropriate
connection for HOMI mode first and then set HOMI mode using
~'lMI.
• When connecting with HOMI cable, perform the settings
in
"Required Settings for HOMI
Connection"
(&page
15).
• OVO-A1UOCI automatically detects audio/video signal supported by the connected HOMI device
and outputs the signal.
To
change the setting,
see
"HOMI Setup"
on
the GUI menu (@"'page 25,
26).
-N,U4
To
disable video or audio
output
from the HDMI terminal, set "Video Out" of "Pure Direct Setup", which
outputs high quality analog audio to "Off".
To
enable the HDMI signal
output
set the Pure Direct mode
to
one of the following setting:
• Pure Direct mode
"Off"
or "User Preset 1" or "User Preset 2"
("*)
("Playing Back High-Quality Audio (pure Direct Function)"
&page
40)
"*
Do this after setting "Pure Direct Setup" - "User Preset 1" or "User Preset 2" - "Video Out" on
GUI
menu to "On"
(&page
30).
I
13
To Next Page
Loading...
