ENGLISH
1.
Home Theater Playback - Playing Back Using Multi-channel System -
I
I Required Settings for
HDMI
Connection
Setting HOMI video output
o Make HOMI Output Signal and HOMI Control Function Settings
"HDMI Setup"
((W'page
25,
26)
o Make the Video Output Signal Setting for the Connected Television
"Video Setup"
((W'
page
26)
o About HOMI Video Resolution Setting
RESOLUTION
• Change the HDMI
video
resolution by pressing
(~).
Switch the output mode
as
follows. Default
settings are underlined.
[
Auto
Source Direct
--
480/576i - 480/576P
:J
(Auto) (Source Direct) (480/576 Interlaced) (480/576 progressiveI
1080P24 1080P 1080i 720P
(1080 progressive, 24-frame) (1080 progressive) (1080 interlaced) (720 progressive)
•
If
the HDMI resolution is not set to ':Auto", set it to correspond with the resolution
of
your television.
Images will not be projected normally if the television resolution and DVD-A1UDCl's output resolution
do not match.
• Audio and video will be temporarily interrupted if the power
of
the connected device currently playing
back
is
turned off, or input
is
switched.
• When you change the HDMI video resolution
of
the DVD-A1UDCI, it takes from a
few
seconds up to
about 10 seconds for validation between the DVD-AlUDCI and the connected device. Audio/video
is
not
output
during this period.
• When outputting deep colour or 1080p, etc.,
we
recommend you use High Speed HDMI cable for
enhanced high-quality playback.
'N.na
When the HDMI
video
resolution
is
set to "1080P24", HDMI
video
signals are
output
from the DVD-
AlUDCI
with
a resolution
of
1080P and a frame rate
of
24 frames per second, regardless
of
the
video
signals on the disc being played. Because of this, when playing discs containing
video
signals recorded
with
a frame rate
of
something other than 24 frames per second, the
movement
of
the picture may be
unnatural.
If
this happens, set the HDMI
video
resolution to something other than
'"
080P24".
15
Setting HOMI Audio Output
• When you press
(5
and set "HDMI Setup" - "Audio Setup" to "Auto"
(~page
25)
on the
GUI
menu.
audio
mode
is
set according
to
the connected device.
• When you want to set the HDMI audio output separately, change according
to
the following table.
• Refer
to
the owner's manual
of
the connected device regarding HDMI audio input specifications
compatible with the connected device.
Device
to
be connected
Setting items
About output signal and speaker settings
Device with the following
DVD-A1
UDCI
outputs a bitstream signal that
is
decoded by
built-in decoder
the connected device.
. Dolby TrueHD
*
In
this case. you cannot make a speaker setting for HDMI
Dolby Digital Plus
Au.t2
audio with the DVD-A1UDCI.
Dolby Digital
Make the setting
with
the connected device.
DTS-HD
*When
(~utting
the Dolby TrueHD or
DTS-HD
audio,
DTS
press
MODE
and set "BD Audio Mode"
to
"HD
AudiO
Output"
(&page
33).
Outputs multi-channel Linear
PCM
audio signals with
Device compatible with
speaker setting by the DVD-A1UDCI.
multi-channel HDMI audio *
For
speaker setting, on the
GUI
menu, "Audio Setup
"
Multi LPCM
input. but not capable
of
BMOn
-
"71ch
Audio
Out"-
"Multi
Channel"
-
"Speaker
speaker setting
for
each
Configuration"
(&page
27).
channel
* BM : Bass Management (means multi-channel speaker
setting)
Device compatible
with
Output
of
multi-channel Linear PCM audio signals from the
multi-channel HDMI audio
Multi LPCM
DVD-AlUDCI.
input.
and capable
of
BM Off
Perform the speaker setting
with
the connected device.
speaker setting for each
* BM : Bass Management (means multi-channel speaker
channel setting)
Device compatible
with
2-
Downmixed 2-channel Linear PCM audio signals
are
output
2ch
from the DVD-A1UDCI.
channel HDMI audio input
Perform the speaker setting
with
the connected device.
Audio signal are not
output
from the DVD-A1UDCl's HDMI
Device not compatible
with
Mute
terminal.
HDMI audio signal input Only video signals are output from the HDMI terminal.
* Make the audio connection.
To Next Page
Loading...
