ENGLISH
o Signals Compatible with DENON LINK Setting and Transmission
The DENON
LINK
setting for the DENON
LINK
version of the connected
AV
Amp
is
as
follows:
Setting items
XLR
Set
the signal
to
be output
from the
XLR
terminal.
Audio Setup
Setting contents
[Terminal Polarity] : Set the polarity of the
XLR
terminal.
•
N.o.rm.a.I
: Normal polarity
• Inversion: Reverse the polarity.
[Gain Up] :
Can
increase output gain when the input sensitivity of a
device connected
via
XLR
is
low.
•
Qfl:
Outputs at standard gain from the
XLR
terminal.
•
On
: Increase the output gain of the
XLR
terminal. Set when the input
sensitity of the connected device is low.
#
The default
DVD-A
1
UDCI
balance model
XLR
audio connectors pin
alignment is
as
shown.
~
CD
GROUND
CV
HOT
®
COLD
3rd Edition
("3rd" displayed near
terminal)
4th Edition
("4th" displayed near
terminal)
"3rd"
"4th"
x
o
o
o
o
o
o
o
o
o
o
o
I
•
N·)j
*
With DENON
LINK
connections,
no
audio signals other than those of
SO
are
output from the HDMI
terminal.
(When "DENON
LINK
Mode"
is
set to "2nd"
and
"HDMI Setup" - "SA-CD Audio Out"
(G"'page
26)
is
set
to "On", the audio signals of Super Audio
CD
are
output from the HDMI terminal.)
DENON LINK Setup
~
[liiIl
S.tth.
'od'o
,'.n"
to
h.
ootpot
from
fh.
DENON LINK
,",m'",!.
Pure Direct Setup
Delau
UIl.dm'lLned.
Makes settings regarding digital audio and video output modes during Pure Direct mode,
as
well
as
display messages. Two types
of
setting
can
be
registered,
Setting items
DENON LINK Mode
Set
the audio output of
DENON
LINK.
Setting contents
[Qtt] :
Do
not use DENON
LINK.
[2nd]
: Output digital audio using DENON
LINK
2nd Edition.
[3rd] : Output digital audio using DENON
LINK
3rd Edition.
[4th] : Output digital audio using
DENON
LINK
4th Edition.
Compatible with jitter-free connection.
For
more information, refer
to
"DENON
LINK
Connection
CD
Making a Jitter-free Connection"
(G"'page
18).
•
HDMI1
: Improve
HDMll
digital signal jitter.
• HDMI 2 : Improve HDMI2 digital signal jitter.
#
• When set to "4th", the HDMI control function becomes available from
the connected device.
• When "4th" is set
and
jitter-free connection is set
up,
audio affected
by the jitter-free function
is
output from the HDMI terminal during
BD
playback. When playing back media other than that, video signal
is
output from the HDMI terminal and audio signal
is
output from the
DENON
LINK
terminal. respectively.
•
To
play
DENON
LINK 4th signals, connect to a
DENON
LINK
4th-
compatible
AV
Amp using
an
HDMI
and
a
DENON
LINK
cable.
• About the 4th setting of the
AV
Amp, see the owner's manual of the
AVAmp.
II
Setting items
User Preset
1/
User Preset 2
This setsthe operating mode
for "User Preset
1"
or "User
Preset
2"
selected by
@.
Setting each of these items
to
"Off"
enables output of
high quality analog signals
free of interference from the
associated circuits.
Setting contents
[Digital Out] : Set whether to output signals
to
the digital audio output
terminal.
•
On..:
Enable digital audio output.
• Off : Disable digital audio output.
[Video Out] : Set option of video output.
• Qn : Enable video output.
• Off : Disable video output. This setting also disables audio output from
the HDMI terminal.
[Display] : Set option for front panel display.
•
Qn
:
Turn
on
display.
•
Off:
Turn
off display.
#
For
more information,
see
"Playing Back High-quality Audio
(Pure
Direct
Function)"
(G"'page
40).
Remote control operation
buttons
.Displaying the menu
'Cancel the menu
.Moves the cursor
'(Up/Down/Left/Rightj
e :Decision the setting
RETURN
o
:Return to previous menu
30
To Next Page
Loading...
