ENGLISH
Audio
Setup
Setting items
7.1ch Audio Out
Setting contents
[Crossover Freq.] : Set the upper limit of the low frequency signals
output from the subwoofer.
o 40Hz/60Hz/8.OJ:I.z/90Hz/100Hz/110Hz/120Hz/150Hz/200Hz/250Hz
: Outputs at below set frequency, each speaker's bass signal
output from the subwoofer. Set this according to the low frequency
reproduction capabilities of the speakers
you
are
using.
o Advanced : Set the low frequency signals to be output from the
signals of the respective speakers to the subwoofer.
Front, Center, Surround, Surr. Back
40Hz/60Hz/8.OJ:I.zI90Hz/1
OOHz/
11
OHz/120Hz/150Hz/200Hz/250Hz
LFE
/ LFE+Main
8.OJ:I.z/90Hz/1
OOHz/
11
OHz/120Hz/150Hz/200Hz/250Hz
r?
When, on the
GUI
menu, "Audio Setup" -
"7.1
ch
Audio
Out"-
"Multi
Channel" - "Speaker Configuration" - "Subwoofer"
is
set to "Yes"
(o:::w'page
27),
you
can
select "LFE" or "LFE+Main".
-N'U·
o Select "Large"
or
"Small" not according to the physical
size
of the
speaker but according to the low frequency reproduction capabilities
based on the frequency set at "Crossover Freq.".
o
On
the
GUI
menu, if the "Audio Setup" -
"7.1
ch
Audio
Out"-
"Multi
Channel" - "Speaker Configuration" item setting is changed, other
settings are automatically changed
as
well.
[Example]
If you set "Front" to "Small", "Subwoofer"
is
set to "Yes"
and
"Large"
cannot
be
selected for "Center", "Surround" and "Surr. Back".
o Audio signal (sampling frequency, number of channels) from the
HDMI output terminal may
be
restricted by the specification
of
the
HDMI audio that
can
be input by the device at the other side.
[Example]
If the HDMI audio specification of the device at the other side is the
5.1
channel,
even
when
DVD-A
1
UDCI
plays back by the
7.1
channel.
the
5.1
channel audio is automatically output.
In
that case, the analog
audio output becomes the
5.1
channel output
as
well.
Setting items
7.1
ch
Audio
Out
Subwoofer
Mode
Set the type
of
lowfrequency
signal to
be
output from the
subwoofer,
Setting contents
o Channel
Level:
Set the volume of the test tone to be the same when
it
is
output from each speaker.
[Mode] : Select a test tone output method.
• AutQ : Automatically switch the test tone output speaker.
•
Manual:
Manually switch the test tone output speaker.
[Start] : Begin outputting the test tone.
Front L / Center / Front R / Surround R /
Surr. Back R / Surr. Back L / Surround L / Subwoofer
"*
When the test tone output stops, press
(5.
[SW
+10dB] : Increase the subwoofer output level by
10
dB.
*
• Off :
Do
not change the subwoofer output level.
•
On:
Increase the subwoofer output level by
+10
dB.
[Default] : Reset
all
channel level settings to factory default.
• No :
Do
not Reset.
•
Yes:
Reset.
o
Distance:
Set the distance between the listening position
and
each
speaker.
[feet]
or
[Meters] : Set the unit of distance.
[Step] : Set the minimum variable width of the distance.
1ft, O.1ft, O.1m, O,01m
[Default] :
Reset
all
distance settings to factory default.
Front L / Front R / Center / Subwoofer / Surround L / Surround R /
Surr. Back L / Surr. Back R :
Select the speaker you want to set.
and
set the distance. Set the value that
is
closest to the measured
distance.
0-6OftorO-18m
r?
• Default
settings:
Front/Center/Subwoofer :
12
feet (3.6 meters)
Surround/Surr.
Back:
10
feet (3.0 meters)
• Set the difference
in
the distance betweem the speakers to less than
20
feet (6.0 meters)
LEE
: Add the low frequency signal of the channel for which the speaker
size
is
set to "small" to the subwoofer signal
and
output it.
LFE+Main : Add the low frequency signal of
all
channels to the subwoofer
signal
and
output it.
I
.'
*:
"SW +10dB" cannot
be
set for "HDMI Setup" - "Audio Setup" - "Multi
LPCM
BM On" - "Channel
Level"
on
the
GUI
menu.
Remote control operation
buttons
SETUP
eD
.Displaying the menu
'Cancel the menu
.Moves the cursor
'(Up/Down/Left/Right)
8 :Decision the setting
RETURN
o
:Return to previous menu
28
To Next Page
Loading...
