The information contained here are property of DIGITAX Automotive Electronics Italy, and extremely confi dential.
Any disclosure, copying, distribution to third
party is strictly prohibited.
45
LIGHT N . 3
245
Enable light n. 3 ON in day- me? - Should it be possible for light number 3 to be ON during the day- me?
The allowed answer is either: 0 (No: disabled) or: 1 (Yes: enabled).
No / Yes
246
Light n. 3 must fl ash? - If Yes light number 3 will fl ash. The allowed answer is either: 0 (No: no fl ash) or: 1 (Yes: fl ash). No / Yes
247
Light n. 3 must go ON in overspeed? - If Yes then light number 3 will go ON in case the actual velocity is higher than the velocity programmed
in Q.200. The allowed answer is either: 0 (No: OFF) or: 1 (Yes: ON).
No / Yes
248 Light n. 3 must go on below overspeed? No / Yes
from Q 249 / available for any possible so ware extension / to Q 251
252
Light n. 3 ON in this tariff -block? - With Yes light number 3 will go ON in the corrisponding tariff -block. The allowed answer is either: 0 (No:
OFF) or: 1 (Yes: ON).
No / Yes
253
Block-number for light n. 3 ON: this is the number of the tariff -block where light number 3 should be ON. The allowed value goes from 0 (min)
to 62 (max).
0 - 62
254
Prog-Date-number for light n. 3 ON: this is the number of the Prog-Date where light number 3 should be ON. The allowed value goes from 0
(min) to 8 (max).
0 - 8
255
State of taximeter for light n. 3 ON: this is the state (or states) of the taximeter in which the light number 3 should be ON.
The allowed values are: 0 (none) - 32 (Hired) - 64 (Stopped) - 128 (ForHire).
Also combina ons are allowed. In that case the values need to be summed together.
For example, to put ON light number 3 in Stopped and also in ForHire the value to program is: 64 + 128 = 192.
For Hire = 128
Stopped = 64
Hired = 32
None= 0
LIGHT N. 4
256
Enable light n. 4 ON in day- me? - Should it be possible for light number 4 to be ON during the day- me?
The allowed answer is either: 0 (No: disabled) or: 1 (Yes: enabled).
No / Yes
257 Light n. 4 must fl ash? - If Yes light number 4 will fl ash. The allowed answer is either: 0 (No: no fl ash) or: 1 (Yes: fl ash). No / Yes
258
Light n. 4 must go ON in overspeed? - If Yes then light number 4 will go ON in case the actual velocity is higher than the velocity programmed
in Q.200. The allowed answer is either: 0 (No: OFF) or: 1 (Yes: ON).
No / Yes
259 Light n. 4 must go on below overspeed? No / Yes
from Q 260 to Q 262 available for any possible so ware extension
263
Light n. 4 ON in this tariff -block? - With Yes light number 4 will go ON in the corrisponding tariff -block. The allowed answer is either: 0 (No:
OFF) or: 1 (Yes: ON).
No / Yes
264
Block-number for light n. 4 ON: this is the number of the tariff -block where light number 4 should be ON. The allowed value goes from 0 (min)
to 62 (max).
0 - 62
265
Prog-Date-number for light n. 4 ON: this is the number of the Prog-Date where light number 4 should be ON. The allowed value goes from 0
(min) to 8 (max).
0 - 8
266
State of taximeter for light n. 4 ON: this is the state (or states) of the taximeter in which the light number 4 should be ON.
The allowed values are: 0 (none) - 32 (Hired) - 64 (Stopped) - 128 (ForHire).
Also combina ons are allowed. In that case the values need to be summed together.
For example, to put ON light number 4 in Stopped and also in ForHire the value to program is: 64 + 128 = 192.
ForHire= 128
Stopped= 64
Hired= 32
None= 0
VARIOUS FUNCTION
267 Must be Euro the default currency? - Establish default currency star ng the trip No=Local currency Yes=Euro No / Yes
268
Disable visualiza on of clock on display? - Should the visualiza on of the clock on the (secondary) display be disabled?
The allowed answer is either: 0 (No: enabled) or: 1 (Yes: disabled).
No / Yes
269
Inhibit clock- me programming from panel? - Should the possibility to program the clock- me from the panel be inhibited?
The allowed answer is either: 0 (No: enabled) or: 1 (Yes: disabled).
No / Yes
270
Disable visualiza on of chronometer? - Should the visualiza on of the chronometer on the display be disabled?
The allowed answer is either: 0 (No: enabled) or: 1 (Yes: disabled).
No / Yes
271
In ForHire show text “F-HIRE” on display? - Should the text “F-HIRE” be shown on the primary display when in ForHire?
The allowed answer is either: 0 (No: show text) or: 1 (Yes: don’t show text).
No / Yes
272
Distance is in yards ? (if not: metres) - The distance in Q.2 to Q.4 is in yards? If not then the distance is in me
tres.
The allowed answer is either: 0 (No: metres) or: 1 (Yes: yards).
0=metres
1=yard
To Next Page
Loading...
Need help?
General
