DFW series indicators DFW_03_12.07_EN_U
46
Storing of the weight and management of the list:
- by pressing the ENTER/PRINT key the current weight value is stored in the list; it is also possible to store the sum of
the weighs;
- by pressing at length the ENTER/PRINT key it is possible to access to the management menu of the list of weighs
(if the “yES” mode has been selected), or one can directly activate the PC connection (if the “yES.dir” mode has been
selected),
- if the list closure is enabled and there is an open list of weighs, by pressing at length the ENTER/PRINT key the
“CLoSE?” message is displayed.
Press ENTER/PRINT to confirm: the display shows the “totAL” message and then the sum of the previous weights
stored blinks for five seconds; the instrument returns to weighing mode after these visualizations.
By pressing C the list is not closed and the next step of the menu is displayed.
- it is possible to import the list of weights in WeighConsole™ (see the manual of the DiniTools™ software) which will
display the list.
Note: the printing function of the ENTER/PRINT key is disabled when the list of weighs is enabled.
Avalaible data in the list of weighs:
The data stored in the list of weighs include:
- progressive number of the weigh
- number of the scale or indication of the text “SUM”
- indication of the closure of the list (in the printing of the list, it is marked with an asterisk next to the number of the scale or
next to the text “SUM” in the last weigh stored)
- date and time
- net weight (equal to the gross weight, also if the tare has been executed).The tare value stored in the list of weighs
is always equal to zero.
Steps of the management menu of the list:
PC.Conn PC connection step; by pressing the ENTER/PRINT key the connection is activated (the “PC.WAit”
message is displayed): it is possible to download the list on PC with WeighConsole™ (see the manual of
the DiniTools™ software) or one can send serial commands to the indicator to manage the memory
(see section “FORMAT OF THE SERIAL COMMANDS”, TECH.MAN.REF.); if the list is empty, the
message “EMPTY” is displayed and the indicator is not connected to the PC.
Prn.LSt List printing on the printer serial port; the printed data are the same of the list that can be downloaded on
PC through serial commands, but without checksum (for the description of the transmitted data, see
“Command for reading the complete list of weighs stored in the memory”, TECH.MAN.REF.).
By pressing the ENTER/PRINT key, the “Print?” message is displayed: press the ENTER/PRINT key to
confirm (the “LiSt..” message is displayed) or the C key to exit from the step without printing.
If one confirms with ENTER/PRINT but the list is empty, the “EE.EMP” message is displayed.
dEL.LSt List deletion from the memory; by pressing the ENTER/PRINT key, the “ErASE?” message is
displayed: press the ENTER/PRINT key to confirm (the “dEL..” message is displayed) or the C key to exit
from the step without deleting the memory.
n.SLAVE Selection of one slave or the sum; by pressing the ENTER/PRINT key, the display shows the “S xx”
message: it is possible to insert the number of the slave or the value “00” to select the sum of the weights.
The step is displayed only if more than one slave are set in the “nuMSL” step.
oFF.MSt It allows to turn off only the master by pressing the ENTER/PRINT key.
Direct access to the PC connection:
The “PC.WAit” message is displayed: it is possible to download the list on PC with WeighConsole™ (see the manual of the
DiniTools™ software) or one can send serial commands to the indicator to manage the memory (see section “FORMAT OF
THE SERIAL COMMANDS”, TECH.MAN.REF.); if the list is empty, the message “EMPTY” is displayed and the indicator is
not connected to the PC.
To Next Page
Loading...
