Need help?Do you have a question about the Dormakaba 79 Series and is the answer not in the manual?
Instructions for maintenance professionals or lock installers.
Defines ASM, ESM, and ADB terms used in the manual.
Contact numbers for technical support for specific lock series.
Lists all parts and tools required for installation.
Exploded view diagrams for ASM, ESM, and cylindrical lock models.
Details on assembling the inside trim for autodeadbolt ASM models.
Instructions for ASM, ESM, and 79T toggle mode for cylindrical locks.
Assembly of autodeadbolt ASM inside trim for 79T toggle mode.
Assembly of cylindrical unit and inside trim for 79M standard mode.
Assembly of inside trim for 79T toggle mode cylindrical locks.
How to check and determine correct mortise handing for installation.
Step-by-step instructions for installing the strike plate and dust box.
Instructions for installing the mortise lock body into the door edge.
Attaching outside housing and inside trim assembly without key override.
How to reverse the outside lever for correct handing and installation.
Testing of inside/outside levers and standard/autodeadbolts.
Initial lock testing before programming for specific series.
Testing the privacy function and keycard lockout.
Testing emergency keycard access and deadbolt override.
Testing lever detection for 79T toggle mode.
Programming locks using the FDU (Front Desk Unit).
Programming locks using the M-Unit for ATLAS system.
Programming locks for multihousing systems.
Programming locks using Aurora/Enterprise software.
How to use the FDU for electronic override.
How to use ATLAS for electronic override.
List of required hardware and PA keycard for override.
Testing levers and deadbolts for 660 Series.
Procedure for activating 660i locks.
Programming users and entering codes for 660 Series.
Testing emergency access and deadbolt override for 660 Series.
Methods for deactivating the deadbolt (thumbturn/lever).
Steps to take if the lock does not respond to codes.
Lists parts and tools for mechanical override installation.
Illustrates the components of the mechanical override lock.
Instructions for using the recodable cylinder with 3 different keys.
How to reverse the mortise handing for ASM models.
Detailed steps for reversing ASM mortise handing.
How to reverse the mortise handing for ESM models.
Specific installation steps for autodeadbolt ASM models.
Specific installation steps for ASM Office models.
Specific installation steps for ASM/ESM Storeroom models.
Instructions for installing the strike for cylindrical models.
Instructions for installing the latch for cylindrical models.
Instructions for installing the cylindrical unit and related spacers.
Details on the inside trim assembly for cylindrical locks.
Instructions for installing outside housing and trim for cylindrical locks.
Instructions for maintenance professionals or lock installers.
Defines ASM, ESM, and ADB terms used in the manual.
Contact numbers for technical support for specific lock series.
Lists all parts and tools required for installation.
Exploded view diagrams for ASM, ESM, and cylindrical lock models.
Details on assembling the inside trim for autodeadbolt ASM models.
Instructions for ASM, ESM, and 79T toggle mode for cylindrical locks.
Assembly of autodeadbolt ASM inside trim for 79T toggle mode.
Assembly of cylindrical unit and inside trim for 79M standard mode.
Assembly of inside trim for 79T toggle mode cylindrical locks.
How to check and determine correct mortise handing for installation.
Step-by-step instructions for installing the strike plate and dust box.
Instructions for installing the mortise lock body into the door edge.
Attaching outside housing and inside trim assembly without key override.
How to reverse the outside lever for correct handing and installation.
Testing of inside/outside levers and standard/autodeadbolts.
Initial lock testing before programming for specific series.
Testing the privacy function and keycard lockout.
Testing emergency keycard access and deadbolt override.
Testing lever detection for 79T toggle mode.
Programming locks using the FDU (Front Desk Unit).
Programming locks using the M-Unit for ATLAS system.
Programming locks for multihousing systems.
Programming locks using Aurora/Enterprise software.
How to use the FDU for electronic override.
How to use ATLAS for electronic override.
List of required hardware and PA keycard for override.
Testing levers and deadbolts for 660 Series.
Procedure for activating 660i locks.
Programming users and entering codes for 660 Series.
Testing emergency access and deadbolt override for 660 Series.
Methods for deactivating the deadbolt (thumbturn/lever).
Steps to take if the lock does not respond to codes.
Lists parts and tools for mechanical override installation.
Illustrates the components of the mechanical override lock.
Instructions for using the recodable cylinder with 3 different keys.
How to reverse the mortise handing for ASM models.
Detailed steps for reversing ASM mortise handing.
How to reverse the mortise handing for ESM models.
Specific installation steps for autodeadbolt ASM models.
Specific installation steps for ASM Office models.
Specific installation steps for ASM/ESM Storeroom models.
Instructions for installing the strike for cylindrical models.
Instructions for installing the latch for cylindrical models.
Instructions for installing the cylindrical unit and related spacers.
Details on the inside trim assembly for cylindrical locks.
Instructions for installing outside housing and trim for cylindrical locks.
General| Type | Mortise Lock |
|---|---|
| Backset | 2-3/4" (70mm) |
| Door Thickness | 1-3/4" (44mm) standard. Other thicknesses available. |
| Material | Steel |
| Strike | Standard strike |
| Handing | Reversible |
| Latchbolt | 1/2 inch throw |
| Deadbolt | 1 inch throw |
| Compliance | ANSI/BHMA A156.13 |
| Finish | Multiple options available |
| Keyway | Multiple options available |
To Next Page
