10 Instructions for use | X-plore 8000 Face Shield X-plore 8000 Helmet PC visor HL1
en | Safety information
X-plore 8000 Face Shield
X-plore 8000 Helmet PC visor HL1
1 Safety information
1.1 General safety instructions
– Before using this product, carefully read these instructions
for use and those of the associated products.
– Strictly follow the instructions for use. The user must fully
understand and strictly observe the instructions. Use the
product only for the purposes specified in the intended use
section of this document.
– Do not dispose of the instructions for use. Ensure that they
are stored and used appropriately by the user.
– Only trained and competent users are permitted to use
this product.
– Use only genuine Dräger spare parts and accessories.
Otherwise, the proper functioning of the product may be
impaired.
– Notify Dräger in the event of any component fault or
failure.
– Comply with all local and national rules and regulations
associated with this product.
– Do not use a faulty or incomplete product. Do not modify
the product.
These instructions for use can be downloaded in other
languages from the Technical Documentation Database
(www.draeger.com/ifu) in electronic form.
1.2 Product-specific safety instructions
– Ensure there is an unobstructed supply of fresh air to the
facepiece.
– Before use, check whether the facepiece is suitable for the
intended application.
X-plore 8000 helmet with PC visor HL1
– Replace the helmet after a violent impact, or if it is
damaged.
– Do not change or remove any parts.
– Always replace the entire internal helmet components.
– The helmet may be damaged by certain substances (e.g.
petrol, paints, adhesive labels, aerosol spray, cleaning
agents).
X-plore 8000 Face Shield
– This is not an industrial safety helmet.
– This bump cap does not offer any protection against falling
or thrown objects, or moving suspended loads.
– This bump cap should not be used instead of an industrial
safety helmet that meets EN 397.
– This bump cap is designed to absorb the energy of an
impact in which the bump cap shell or internal helmet
components are partially destroyed or damaged. This
damage may not be immediately visible. Therefore,
replace each bump cap after a violent impact.
– This bump cap must fit, or be adjusted to fit the user's
head size, in order to provide appropriate protection.
– If original bump cap parts are changed or removed, the
bump cap may not provide sufficient protection.
– Do not alter the bump cap so that parts not recommended
by Dräger can be added.
– Only use paints, solvents, adhesives or self-adhesive
labels that are specified in these instructions for use for
the bump cap.
– Use in explosion-hazard areas:
Devices or components that are used in explosion-hazard
areas, and have been tested and approved in accordance
with national, European or international explosion
protection directives, may only be used under the
conditions stipulated in the approval, and while following
the relevant legal regulations. Devices and components
may not be changed. The use of defective or incomplete
parts is not permitted. The applicable conditions must be
observed when repairing these devices or components.
2 Conventions in this document
2.1 Meaning of the warning notices
The following warnings are used in this document to alert the
user to potential dangers. The meanings of the warning
notices are defined as follows:
3 Description
3.1 Product overview
(see fold-out page, figures A, B)
Warning
sign
Signal word Classification of the warning
notice
WARNING Indicates a potentially hazard-
ous situation. If not avoided, it
could result in death or serious
injury.
NOTICE Indicates a potentially hazard-
ous situation. If not avoided, it
could result in damage to the
product or environment.
1 Support ring assembly
2 Sweatband
3 Support ring
4 Padding
5 Face shield sealing
6 Bump cap shell
7 Visor frame mounting
8 Visor frame
9 Visor fastener
10 Visor shield
11 Head straps
12 Chin strap
13 Helmet shell
To Next Page
Loading...
Need help?
General
