Drehmo D 30 - Page 44

DREHMO GmbH
Zum Eichstruck 10
57482 Wenden/Germany
DREHMO
EU Declaration of Conformity /
Declaration of Incorporation in compliance
with Machinery Directive
As the manufacturer DREHMO GmbH hereby declare that the electro-mechanical DREHMO®
actuators and accompanying components from the following series
Standard
D(R) 30 Ex - D(R) 2000 Ex
DP(R) 75 Ex - DP(R) 1800 Ex
comply with the fundamental requirements of the ATEX Directive (2014/34/EU), the Electromag-
netic Compatibility (2014/30/EU), the Low Voltage Directive (2014/35/EU) and the Machinery
Directive (2006/42/EC).
EU Deciaration of Conformity according to the Council Directive on the approximation of
laws of the member States relating to the ATEX Directive (2014/34/EU), the Electromagnet-
ic Compatibility Directive (2014/30/EU) and the Low Voltage Directive (2014/35/EU)
Notified body: TÜV SÜD Product Service GmbH - Zertifizierstelle -
Identification number: 0123
Address: TÜV SÜD Ridlerstraße 65; 80339 München
Certification number: TPS 23 ATEX Q 078524 0008
Type approval test certificates: PTB 15 ATEX 1014 X
The following harmonised Standards in terms of the specified directives have been applied:
ATEX Directive (2014/34/EU)
EN IEC 60079-0:2018 EN 60079-1:2014
EN IEC 60079-7:201 5/A1:2018 EN 60079-11:2012
EN ISO 80079-36:2016 EN ISO 80079-37:2016
EN 1127-1:2019
Electromagnetic Compatibility Directive (2014/30/EU)
EN 61000-6-2:2005/AC:2005 EN 61000-6-4:2007/A1:2011
Low Voltage Directive (2014/35/EU)
EN 61010-1:2010/A1:2019 EN 60034-1:2010/AC:2010
Declaration of Incorporation in terms of EC Machinery Directive (2006/42/EC) Appendix II B
The following harmonised Standards in terms of the Machinery Directive (2006/42/EC) have been
applied:
EN ISO 12100:2010
DREHMO® actuators are intended for assembly with valves. The commissioning phase should
only be implemented if it has been ensured that the final machinery in which the DREHMO®actu-
ators are installed complies with the regulations of the EC Machinery Directive (2006/42/EC).
DREHMO® as manufacturer declares herewith, that the above mentioned linear thrust units meet
the following basic requirements of the EC Machinery Directive (2006/42/EC):
Appendix I, articles: 1.1.2,1.1.3, 1.1.5, 1.2.1, 1.2.6, 1.3.1,1.3.7, 1.5.1, 1.6.3, 1.7.1, 1.7.3, 1.7.4
The manufacturer is obliged to electronically submit the documents for the partly completed ma 
chinery to national authorities on request. The relevant technical documents pertaining to the
machinery according to Appendix VII part B have been complied.
Person responsible for documentation:
Dr. Rüdiger Stenzel, Zum Eichstruck 10, 57482 Wenden/Germany
K. Ewald/General Manager
Wenden, 2023-10-19
This deciaration does not imply an assurance of properties. The safety precautions in the supplied product documents are to be ob-
served. This deciaration shall lose its validity in the event of unauthorised modification of the equipment.