DSC MAXSYS PC4020 Installation Manual

i
Table of Contents
Section 1: Introduction 1
1.1 Out of the Box ............................................................................ 1
1.2 Specifications and Features ..................................................... 1
Section 2: Installation and Wiring 2
2.1 Planning the System ................................................................. 2
2.2 Terminal Descriptions .............................................................. 2
2.3 Wire Routing for Power and Non-Power Limited ............... 2
2.4 Current Ratings – Alarm Control Panel and Modules ........ 2
2.5 Combus Operation and Wiring .............................................. 3
2.6 Zone Wiring ............................................................................... 4
2.7 Specialized Zone Wiring .......................................................... 5
2.8 Programmable Output Wiring ................................................ 5
2.9 AML Device Wiring .................................................................. 5
2.10 Wiring Powered Devices (AUX, SAUX+) .............................. 6
2.11 Telephone Line Wiring ............................................................. 7
2.12 Bell Output Wiring (BELL+ and BELL-) ................................ 7
2.13 Earth Ground Wiring ............................................................... 7
2.14 Applying Power (AC and Battery) ......................................... 7
2.15 Lithium Batteries ....................................................................... 8
Section 3: How to Program 9
3.1 Introduction to Programming ................................................. 9
3.2 Programming by Reference Number ..................................... 9
3.3 Programming Decimal Data .................................................... 9
3.4 Programming Hexadecimal Data ......................................... 10
3.5 Programming Toggle Options .............................................. 10
Section 4: Module Enrollment 11
4.1 Enrolling Keypads and Modules .......................................... 11
4.2 Deleting Modules .................................................................... 11
4.3 Confirming Modules .............................................................. 12
4.4 Enrolling AML Devices .......................................................... 12
Section 5: Partitions and Zones 13
5.1 Zone Supervision .................................................................... 13
5.2 Creating Partitions .................................................................. 13
5.3 Adding Zones to Partitions ................................................... 14
5.4 Zone Programming ................................................................. 14
Section 6: Keypad Operation 18
6.1 Partition Keypads .................................................................... 18
6.2 Global Keypads ....................................................................... 18
6.3 Keypad Toggle Options ......................................................... 18
6.4 Keypad Time-out .................................................................... 19
6.5 Keypad Blanking ..................................................................... 19
6.6 Fire, Auxiliary and Panic Keys .............................................. 19
6.7 Keypad Lockout ...................................................................... 19
6.8 Keypad Tampers ..................................................................... 20
6.9 Alarm Memory Display ......................................................... 20
6.10 Zone Bypass Display .............................................................. 20
6.11 Function Key Programming .................................................. 20
Section 7: Installer and Access Codes 22
7.1 Installer’s Code ........................................................................ 22
7.2 Installer-Programmed Access Codes ................................... 22
7.3 Programming Access Codes .................................................. 22
7.4 Modify An Existing Code ...................................................... 24
7.5 Change User Code Options ................................................... 24
7.6 Delete An Existing Code ........................................................ 25
7.7 Special Codes ........................................................................... 25
7.8 Guard Code .............................................................................. 26
7.9 Access Code Options .............................................................. 26
7.10 Access Levels ........................................................................... 26
Section 8: Arming and Disarming 27
8.1 Arming and Disarming Options ...........................................27
8.2 Automatic Arming ..................................................................27
Section 9: Entry and Exit Delay 28
9.1 Entry and Exit Delay Times ...................................................28
9.2 Entry and Exit Delay Options ................................................28
Section 10: System Programming 29
10.1 AC/DC Power Options ..........................................................29
10.2 Bell Circuit Supervision ..........................................................29
10.3 Clock Options ...........................................................................29
10.4 Event Messages ........................................................................30
10.5 Swinger Shutdown ..................................................................30
10.6 Tampers ....................................................................................30
10.7 Telephone Line Supervision ..................................................31
10.8 Test Transmissions ..................................................................31
10.9 Transmission Delay .................................................................31
10.10 Cross Zone (Police Code) Alarm ..........................................32
10.11 System Label ...........................................................................32
10.12 Hourly Print ............................................................................32
Section 11: Programmable Outputs 33
11.1 Main Panel Outputs ................................................................33
11.2 Programming Output Options for Modules .......................33
11.3 Programmable Output Options ............................................33
11.4 Output Pulse Times .................................................................35
Section 12: Communications Programming 37
12.1 Telephone Numbers ................................................................37
12.2 Account Numbers ...................................................................37
12.3 Dialing Parameters ..................................................................37
12.4 Communicator Toggle Options .............................................37
12.5 Dialer Direction ........................................................................39
12.6 Communicator Formats ..........................................................39
12.7 Reporting Codes ......................................................................40
Section 13: Downloading 41
13.1 Downloading Options ............................................................41
13.2 Periodic Call-up .......................................................................41
13.3 PC-Link .....................................................................................41
Section 14: Event Scheduling 42
14.1 Date Schedules .........................................................................42
14.2 Holiday Groups .......................................................................42
14.3 Open/Close Suppression .......................................................42
14.4 Arming/Disarming Schedules ..............................................43
14.5 Scheduled AMS-220/220T Smoke Detector Test ................43
Section 15: LINKS Communications 44
15.1 LINKS1000 (Cellular Communications) ..............................44
15.2 LINKS2XXX (Long-range Radio Communications) ...........44
15.3 T-Link TCP/IP Communications) ........................................44
Section 16: Diagnostics and Troubleshooting 45
16.1 General Diagnostics ................................................................45
16.2 Restoring Factory Default Programming .............................45
16.3 Hardware Reset .......................................................................45
16.4 Viewing Trouble Conditions .................................................45
16.5 System Fault Squawk ..............................................................46
• Appendix A: Reporting Codes 48
• Appendix B: Zone Reporting Codes 51
• Appendix C: ASCII Characters 52

DSC MAXSYS PC4020 Specifications

General

Brand	DSC
Model	MAXSYS PC4020
Category	Security System
Language	English