Dynapac CC1300 - Function Description

Machine description
ICC1300-1EN3.pdf 2011-10-10
Function description
No Designation Symbol FunctionNo Designation Symbol Function
1. Starter switch Positions 1-2: Shut off position, key can be
removed.
1. Starter switch Positions 1-2: Shut off position, key can be
removed.
Position 3a: All instruments and electric controls
are supplied with power.
Position 3a: All instruments and electric controls
are supplied with power.
Position 3b: Glowing. Hold the starter switch in this
position until the lamp goes out. The starter motor
is activated in the next position.
Position 3b: Glowing. Hold the starter switch in this
position until the lamp goes out. The starter motor
is activated in the next position.
Position 3c: Starter motor activation.Position 3c: Starter motor activation.
2. Throttle control In forward position, the engine idles.
In backward position, the engine runs at full speed.
2. Throttle control In forward position, the engine idles.
In backward position, the engine runs at full speed.
3. Emergency stop When pressed, the emergency stop is activated.
The engine switches off and the brakes are
activated. Brace yourself for a sudden stop.
3. Emergency stop When pressed, the emergency stop is activated.
The engine switches off and the brakes are
activated. Brace yourself for a sudden stop.
4. Vibration On/Off. Switch Press once and release to switch vibration on.
Press again to switch the vibration off.
4. Vibration On/Off. Switch Press once and release to switch vibration on.
Press again to switch the vibration off.
5. Handbook compartment Pull up and open the top of the compartment for
access to handbooks.
5. Handbook compartment Pull up and open the top of the compartment for
access to handbooks.
6. Forward/Reverse lever The engine can only be started when the lever is in
neutral. The engine will not start if the
forward/reverse lever is not in the neutral position.
Direction of travel and speed of the roller is
regulated with the forward/reverse lever. Move the
lever forward to drive the roller forwards, etc.
The speed of the roller is proportional to the
distance of the lever from the neutral position. The
further the lever is from the neutral position, the
higher the speed.
6. Forward/Reverse lever The engine can only be started when the lever is in
neutral. The engine will not start if the
forward/reverse lever is not in the neutral position.
Direction of travel and speed of the roller is
regulated with the forward/reverse lever. Move the
lever forward to drive the roller forwards, etc.
The speed of the roller is proportional to the
distance of the lever from the neutral position. The
further the lever is from the neutral position, the
higher the speed.
7. Seat switch Remain seated at all times when operating the
roller. If the operator stands up during operation, a
buzzer sounds. After 4 seconds the brakes are
activated and the engine stops.
7. Seat switch Remain seated at all times when operating the
roller. If the operator stands up during operation, a
buzzer sounds. After 4 seconds the brakes are
activated and the engine stops.
8. Fuse box (on control column) Contains fuses for the electrical system. See under
the heading ‘Electrical system’ for a description of
fuse functions.
8. Fuse box (on control column) Contains fuses for the electrical system. See under
the heading ‘Electrical system’ for a description of
fuse functions.
9. Instrument cover Lowered over the instrument plate to protect the
instruments from the weather and sabotage.
Lockable
9. Instrument cover Lowered over the instrument plate to protect the
instruments from the weather and sabotage.
Lockable
12. Sprinkler, switch (Option) Upper position = switching on of flow of water to
drum.
Intermediate position = Sprinkling switched off
Lower position = switching on of water to drum via
forward/reverse lever. The flow of water can be
controlled by means of the sprinkler timer (13).
12. Sprinkler, switch (Option) Upper position = switching on of flow of water to
drum.
Intermediate position = Sprinkling switched off
Lower position = switching on of water to drum via
forward/reverse lever. The flow of water can be
controlled by means of the sprinkler timer (13).
13. Sprinkler timer (Optional) Variable adjustment of water flow from 0-100%.
Only works when AUTO (12) is pressed in.
13. Sprinkler timer (Optional) Variable adjustment of water flow from 0-100%.
Only works when AUTO (12) is pressed in.
28