Eaton BiWire Flexi - Contents; Table of Contents

2
INSTALLATION AND OPERATION MANUAL 25-16732-A November 2019 www.eaton.com
Contents
CONTENTS
CONTENTS ....................................... 2
1. INTRODUCTION ................................. 3
1.1 PURPOSE ..................................... 3
2. THE BIWIRE FLEXI FIRE DETECTION & ALARM SYSTEM 3
2.1 CONTROL AND INDICATION EQUIPMENT (CIE) ....... 4
2.2 POWER SUPPLY EQUIPMENT (PSE) ................ 5
2.3 EOLM-3 ....................................... 6
2.4 EOLM-1 ....................................... 6
2.5 EOLR ......................................... 6
2.6 SYSTEM WIRING ................................ 7
2.7 STATUS INDICATIONS ........................... 8
2.8 CONTROL PANEL INPUTS AND OUTPUTS ........... 9
Auxiliary Output ................................ 9
Class Change .................................. 9
Fire Relay .....................................10
Fault Relay ....................................10
Interlink Relay ..................................10
Detector Zone Inputs ............................11
Conventional Sounder Circuits .....................11
Repeater I/O ...................................11
2.9 OPTION BOARD (FRE/FPE/ZONAL RELAYS) ..........11
Fire Alarm Routing Equipment (FRE) ................11
Fire Protection Equipment (FPE) ...................11
Zonal Relay Contacts ............................11
3. INSTALLATION INSTRUCTIONS ................... 12
3.1 BEFORE YOU BEGIN .............................12
3.2 CABLING ROUTING & DEVICE INSTALLATION ........12
3.3 PANEL INSTALLATION ...........................13
Mounting the Panel .............................13
Connecting the Mains Supply ......................15
Connecting the Battery Supply .....................15
Battery Connections .............................16
Connecting the Zone Cables ......................16
Connecting the Input/Output Cables ................17
Interlinking Two Panels ...........................17
Connecting a Repeater Panel ......................17
3.4 OPTION BOARD INSTALLATION .................. 18
Connecting the FRE and FPE Outputs .............. 18
Connecting the Zonal Outputs .................... 18
3.5 PANEL CONFIGURATION .........................19
Silence Mode Disabled ...........................19
Silence Mode Enabled ...........................19
Zone Configuration ..............................19
3.6 DETECTOR FITTING ............................ 20
3.7 INSTALLATION TESTING ......................... 20
Initial Power-up Check ........................... 20
Zone Fire Detection Check ....................... 20
Zone Fault Detection Check ...................... 20
Battery Fault Detection Check .................... 20
Fire Outputs & Battery Check ..................... 21
4. COMMISSIONING & SYSTEM HANDOVER. . . . . . . . . . 21
4.1 COMMISSIONING ............................. 21
4.2 SYSTEM HANDOVER ........................... 21
5. MAINTENANCE ................................ 22
5.1 DAILY TESTING ................................ 22
5.2 WEEKLY TESTING .............................. 22
5.3 QUARTERLY TESTING ........................... 22
5.4 YEARLY TESTING ............................... 22
6. OPERATING INSTRUCTIONS ..................... 23
6.1 MULTI-FUNCTION BUTTONS ..................... 23
6.2 SILENCE FIRE ALARM DEVICES .................. 23
6.3 SOUND FIRE ALARM DEVICES ................... 23
6.4 RESET SYSTEM ................................ 23
6.5 MUTE BUZZER ................................ 24
6.6 ENABLE / DISABLE ............................. 24
6.7 INDIVIDUAL ZONE TEST ......................... 25
6.8 LAMP TEST ................................... 25
6.9 SELF-TEST MODE .............................. 26
6.10 WALK TEST MODE ............................ 26
7. TECHNICAL SPECIFICATION ...................... 27
7.1 PANEL SPECIFICATION .......................... 27
7.2 PSE SPECIFICATION ............................ 28
7.3 EOLM-3 SPECIFICATION ......................... 28
7.4 EOLM-1 SPECIFICATION ......................... 28
7.5 OPTION BOARD SPECIFICATION .................. 29
7.6 CABLE SPECIFICATION .......................... 29
8. SYSTEM CALCULATIONS ........................ 29
8.1 ZONE LOADING IN NORMAL CONDITION .......... 29
8.2 ZONE LOADING IN ALARM CONDITION ............ 30
8.3 BATTERY STANDBY TIME ........................ 30
9. MANUFACTURERS CONTACT DETAILS ............ 31