Eaton Scantronic i-on10 - Page 67

Log Messages
Page 67
"Entry Stray Z=="
Stray on entry alarm at zone n
"Ext WD Fault Z==="
A warning device has reported a
fault through zone n
"Ext WD Restr Z==="
The fault reported through zone n
by a warning device has been
restored
"Fire Reset"
User reset system after fire alarm
"Fire Z== Alarm"
Fire alarm on zone n
"Fire Z== Restore"
Fire alarm on zone n restored
"HU == Alarm"
Hold Up alarm at keypad n
"HUA Cnf RF HD U---"
Hold Up Alarm confirmed by radio
HUD belonging to user
"HUA Cnf RF MD U---"
Hold Up Alarm confirmed by radio
Man Down transmitter belonging to
user n
"HUA Conf Bus# Tamp"
Hold Up Alarm by a bus tamper
"HUA Conf HD =="
Hold Up Alarm confirmed on
keypad n HUA keys
"HUA Conf Panel Lid"
Hold Up Alarm confirmed by panel
lid tamper
"HUA Conf. ==ER"
Hold Up Alarm has been confirmed
by a missing external prox reader
on keypad n
"HUA Confirm =="
Hold Up Alarm confirmed on
keypad HUA keys
"HUA Confirm Bell #"
Hold Up Alarm confirmed by
control unit Tamper Return (TR)
"HUA Confirm WAM=="
Hold Up Alarm confirmed by
tamper on WAM n
"HUA Confirm Z==="
Hold Up Alarm confirmed on wired
zone n
"HUA Confirm"
Hold Up Alarm confirmed on device
"HUA Restore P#"
Hold Up alarm at keypad restored
for partition n
"HUA Restore"
Hold Up Alarm has been restored
"HUA Z== Alarm"
Hold Up alarm on zone n
"HUA Z== Restore"
Hold Up alarm restored on zone n
"HUD Fault Rst Z==="
A hold up device fault reported on
zone n was restored
"HUD Fault Z==="
A hold up device reported a fault
on zone n
"Inv Login Attpt KP"
Invalid access code entered on
keypad
"Inv Login Attpt PX"
Invalid prox tag presented to
keypad
"Inv Login Attpt RM"
Invalid remote access attempt
"K== Excess Keys"
Excess keys tamper at keypad n
"Key Sw Ptn # PtSet"
Partition part set from keyswitch
"Key Sw Ptn # Set"
Partition n set from keyswitch
"Key Sw Ptn # Unset"
Partition n unset from keyswitch
"Key Sw System PtSet"
System part set from keyswitch
"Key Sw System Set"
System set from keyswitch
"Key Sw System Unset"
System unset from keyswitch
"Keypad == added"
New keypad n added to system
"Keypad == found"
New keypad n found on bus
"Kpd == deleted"
Keypad deleted from system
"Lid Tamper Restore"
Control unit lid closed
"Lockset Z=== Set"
Zone n with type "lock set" was
closed (If Inverted attribute is set to
"normal")
"Lockset Z=== Unset"
Zone n with type "lock set" was
opened (If Inverted attribute is set
to "normal")
"Login Keypad"
Valid access code entered on
keypad
"Login Prox"
Valid prox tag presented to keypad
"Low Batt = Restore"
Control unit battery no longer low
"Low Battery ="
Control unit battery low
"Missing == Rstr"
Missing keypd n restored to bus
"Missing =="
Keypad n missing from bus
"Missing ==ER Rs"
An External prox Reader
connected to keypad n has been
re-connected
"Missing ==ER"
An External prox Reader
connected to keypad n has gone
missing (possibly disconnected
from the keypad)
"Occupancy Set P#"
Set but with Occupancy zone(s)
open
"Panel A/C Fail"
AC power failure at control unit
"Panel A/C Restore"
AC power restored at control unit
"Panel lid open"
Control unit lid open
"Remote Reset"
User reset system remotely
"Set Fail Z=="
Setting failed at zone
"Soak Fail Z== Alm"
Zone n on soak test failed
"Soak Fail Z== Tmp"
Zone n on soak test tampered
"Software Changed"
New control unit software has been
installed
"System Error"
Control unit has fault in main
processor
"System Rearmed"
User rearmed the system
"System Startup"
The system restarted after a power
fail (mains and battery)
"Tamper == Rstr"
Tamper at keypad n restored
"Tamper =="
Tamper at keypad n
"Tamper ==ER Rst"
Tamper at external reader n
restored
"Tamper ==ER"
Tamper at external reader n
"Tamper Z== Restore"
Zone n tamper restored
"Tamper Z=="
Zone n tamper
"Tech Z== Alarm"
Technical alarm on zone n
"Tech Z== Restore"
Technical alarm on zone n restored
"U-- Change U=="
User n changed their password
"U-- Config Change"
User n changed programming
configuration
"U-- Delete U=="
User n deleted another User n from
system
"U--- Duress Restr"
User n keyed in a Duress code to
unset the system (part setting
system)
"U--- Duress"
User n keyed in a Duress code to
set the system (part setting
system)
"U--- O/P === Off"
User defined output swittched on
by user n