CONTENTS
1.0 System Overview ����������������������������������������������������������������������������������������������������������������������������������� 1
1�1 System Description ����������������������������������������������������������������������������������������������������������������������������������������� 3
1�1�1 MVP Display: ���������������������������������������������������������������������������������������������������������������������������������������� 3
1�1�2 EDC-33T: ��������������������������������������������������������������������������������������������������������������������������������������������� 3
1�1�3 Probes, Transducers and Modules: ��������������������������������������������������������������������������������������������������������� 3
1�1�4 Wiring & Extension Cables: ������������������������������������������������������������������������������������������������������������������� 4
1�2 Operational Overview: ����������������������������������������������������������������������������������������������������������������������������������� 4
1�3 Installation Overview: ������������������������������������������������������������������������������������������������������������������������������������� 4
1�4 Password Protection: �������������������������������������������������������������������������������������������������������������������������������������� 5
1�4�1 Level #1 Password (Maintenance): ��������������������������������������������������������������������������������������������������������� 5
1�4�2 Level #2 Password (OEM/Experimental): ������������������������������������������������������������������������������������������������ 6
2.0 Hardware Installation ������������������������������������������������������������������������������������������������������������������������� 7
2�1 Important Information and Initial Check Out: ���������������������������������������������������������������������������������������������������� 9
2�2 Review the "EDC Wiring Work Sheets:" ��������������������������������������������������������������������������������������������������������� 10
2�3 Verify You Have all the Probes, Modules, Transducers and Cables: ������������������������������������������������������������������� 10
2�4 Installing the MVP Display: ��������������������������������������������������������������������������������������������������������������������������� 10
2�5 Install the Temperature Probes: ���������������������������������������������������������������������������������������������������������������������� 11
2�6 Install the Pressure Transducers: ��������������������������������������������������������������������������������������������������������������������� 12
2�7 Install the Interface Circuit for Annunciators: ��������������������������������������������������������������������������������������������������� 14
2�8 Install the Interface Circuit for Flap and Trim Pots (Optional): ��������������������������������������������������������������������������� 15
2�9 Install the Interface Circuit for the Gear Position, Unsafe Indicator and Gear Warning (Optional): ���������������������� 15
2�10 Install the CO Guardian CO Detector (Optional): ����������������������������������������������������������������������������������������� 16
2�11 Install the Shunt: ����������������������������������������������������������������������������������������������������������������������������������������� 16
2�12 Install the Fuel Flow Transducer: ������������������������������������������������������������������������������������������������������������������ 17
2�13 Install the P-300C Fuel Level Probes: ������������������������������������������������������������������������������������������������������������ 18
2�14 Install the P-300M Magnetic Fuel Level Sender: �������������������������������������������������������������������������������������������� 18
2�15 Install the Resistive Fuel Level Module (RFLM-4-X): ����������������������������������������������������������������������������������������� 19
2�16 Install the Voice Alarm Control Panel (AV-17CP) (Optional): �������������������������������������������������������������������������� 19
2�17 Install the Intensity Control Pot (CP-1) (Optional): ������������������������������������������������������������������������������������������ 19
2�18 Install the Master Warning (red) and Caution (yellow) Lights (Optional): ��������������������������������������������������������� 20
2�19 Install the USB-6A (Optional): ��������������������������������������������������������������������������������������������������������������������� 20
2�20 Install the FM-SC or AC-1 Converter (Optional): ������������������������������������������������������������������������������������������� 20
2�21 Install the BC-5xx (Optional) ����������������������������������������������������������������������������������������������������������������������� 20
2�22 Install the NA-1 (Optional) �������������������������������������������������������������������������������������������������������������������������� 20
2�23 Install any Additional Modules (Optional): ��������������������������������������������������������������������������������������������������� 20
2�24 Installing the EDC-33T: ������������������������������������������������������������������������������������������������������������������������������� 21
3.0 Install the EDC Wire Harnesses and Route Wires �������������������������������������������������������������� 23
3�1 Attach the three EDC 37-pin wire harnesses to the EDC: ��������������������������������������������������������������������������������� 25
3�2 Connect the EDC Harness to the Temperature Probes:�������������������������������������������������������������������������������������� 25
3�3 Connect the EDC Harness to the Pressure Transducers: ������������������������������������������������������������������������������������ 25
3�4 Connect the EDC Harness to the Shunt: ���������������������������������������������������������������������������������������������������������� 26
3�5 Connect the EDC Harness to the Fuel Flow Transducer: ������������������������������������������������������������������������������������ 26
3�6 Connect the RFLM-4-x Harness to the EDC Connector and to the Resistive Fuel Level Sensors: ����������������������������� 27
vii