3�7 Connect the EDC Harness to the Capacitive Fuel Level Probes: ������������������������������������������������������������������������� 27
3�8 Connect the EDC Harness to the P-300M Magnetic Fuel Level Senders: ������������������������������������������������������������ 28
3�9 Connect the EDC Harness (Volts Measurement Pin) to the Bus: ������������������������������������������������������������������������� 28
3�10 Connect the EDC Harness to the N1 and/or N2 Tach Generator: ������������������������������������������������������������������� 28
3�11 Connect the EDC Harness to the VI-221's (Voltage Interface Units): ���������������������������������������������������������������� 28
3�12 Connect the EDC Harness to Power and Ground: ����������������������������������������������������������������������������������������� 29
3�13 Route the EDC RS422 Wires to the MVP Connector: ������������������������������������������������������������������������������������� 29
4.0 Install the MVP Wire Harness and Route Wires ����������������������������������������������������������������� 31
4�1 Attach the MVP 25-pin D-sub Connector to the MVP: �������������������������������������������������������������������������������������� 33
4�2 Connect the EDC RS422 Wires to the MVP RS422 Wires: ������������������������������������������������������������������������������� 33
4�3 Connect the MVP Harness to the Master Warning and Caution Lights (Optional): ���������������������������������������������� 33
4�4 Connect the MVP Harness to the Voice Alarm Control Panel (AV-17CP) (Optional): ������������������������������������������� 33
4�5 Connect the MVP Harness to the Audio Panel (Optional): �������������������������������������������������������������������������������� 34
4�6 Connect the MVP Harness to the External Intensity Control Pot (CP-1) (Optional): ���������������������������������������������� 34
4�7 Connect the MVP Harness to the Moving Map Data Out from the GPS (Optional): �������������������������������������������� 34
4�8 Connect the MVP Harness to the Fuel Data Input on the GPS (Optional): ���������������������������������������������������������� 34
4�9 Connect the MVP "Transmit Lockout Input" pin to the Transmit Key (Optional): �������������������������������������������������� 35
4�10 Connect the MVP Harness to Power and Ground: ����������������������������������������������������������������������������������������� 35
4�11 Connect the MVP Harness to the CO-Guardian CO Detector (Optional): �������������������������������������������������������� 35
4�12 Connect to the MVP RTDO Port (Optional): �������������������������������������������������������������������������������������������������� 35
5.0 Mandatory System Setup and Checkout �������������������������������������������������������������������������������� 37
5�1 Power-On Checkout: ������������������������������������������������������������������������������������������������������������������������������������ 39
5�2 Perform all Steps listed in the "MVP-50T Setup Checklist": ������������������������������������������������������������������������������� 39
5�3 Ground Run Checkout: ��������������������������������������������������������������������������������������������������������������������������������� 39
5�4 First Flight Checkout: ������������������������������������������������������������������������������������������������������������������������������������ 40
5�5 Read the "Warranty/Agreement" and the "Important Notice": ������������������������������������������������������������������������ 40
5�6 POH/AFM Supplement: �������������������������������������������������������������������������������������������������������������������������������� 40
6.0 Installation Data ���������������������������������������������������������������������������������������������������������������������������������� 41
6�1 Instructions for Continued Airworthiness (ICA): ����������������������������������������������������������������������������������������������� 43
6�2 Airworthiness Limitations: ����������������������������������������������������������������������������������������������������������������������������� 43
6�3 Working With Connectors: ��������������������������������������������������������������������������������������������������������������������������� 43
6�3�1 Installing the Over-Lap Connector onto Copper or TC Wire: ������������������������������������������������������������������� 43
6�3�2 Installing a D-sub Pin onto a TC or Tin Copper Wire: ����������������������������������������������������������������������������� 44
MVP-50T 25-pin D-sub Connector Wiring Diagram ���������������������������������������������������������������������������������������������� 45
EDC Wiring (Top Connector) �������������������������������������������������������������������������������������������������������������������������������� 46
EDC Wiring (Middle Connector) �������������������������������������������������������������������������������������������������������������������������� 47
EDC Wiring (Bottom Connector) ��������������������������������������������������������������������������������������������������������������������������� 48
Template for MVP Cutout ������������������������������������������������������������������������������������������������������������������������������������� 49
Template for EDC ������������������������������������������������������������������������������������������������������������������������������������������������ 50
7.0 Troubleshooting ����������������������������������������������������������������������������������������������������������������������������������� 51
7�1 MVP or EDC Problem: ���������������������������������������������������������������������������������������������������������������������������������� 53
7�2 Pressure Problem with one Function: �������������������������������������������������������������������������������������������������������������� 54
7�3 Temperature Problem on all Channels: ����������������������������������������������������������������������������������������������������������� 54
7�4 Temperature Problem with one Function: �������������������������������������������������������������������������������������������������������� 55
viii