Emerson FB1100 - Page 82

FB1100 Flow Computer Instruction Manual
D301752X012
November 2023
68 Index
Figures
1-1. Emerson FB1100 Flow Computer ................ 2
1-2. Retaining Clamps and Tie Holes for
Tamper-resistant Seals .................................... 6
1-3. HMI Module with LCD .................................. 8
1-4. HMI Module without LCD ............................. 9
1-5. External FBxWifi Antenna ........................... 10
2-1. FB1100 Dimensions (w/Multivariable
Sensor) ............................................................. 16
2-2. Front End Cap (w/Retaining Clamp) .......... 17
2-3. Retaining Clamp in Place ........................... 18
2-4. Retaining Clamp and Screw ....................... 18
2-5. Removing/Tightening the End Cap with
Prybar ............................................................... 18
2-6. Front and Rear End Caps............................ 19
2-7. Removing Front and Rear End Caps ......... 19
2-8. Transmitter with Coplanar Flange ............ 20
2-9. Transmitter (w/Coplanar Flange & Optional
Flange Adapters) ............................................. 21
2-10. Transmitter (w/Traditional Flange &
Optional Flange Adapters) ............................. 21
2-11. Bolt Installation ......................................... 22
2-12. O-rings (w/Flange Adapters ..................... 22
2-13. Traditional Flange Mounting Kit ............. 24
2-14. Coplanar Mounting Kit ............................. 25
2-15. Housing Rotation Set Screws .................. 26
2-16. Ground Lug ............................................... 27
2-17. Terminal Plate ........................................... 28
2-18. DC Power Connections ............................. 31
2-19. Connecting the Battery Pack ................... 32
2-20. Attaching Mounting Hardware to the
Solar Panel ....................................................... 34
2-21. Integral mounted solar panel ................. 35
2-22. Solar panel remote mounted (pole
mounted) ......................................................... 37
2-23. Wiring Solar Power ................................... 38
2-24. Adjusting Solar Panel Tilt Angle .............. 38
2-25. Connecting a Device to COM1 Using RS-
232 .................................................................... 40
2-26. Connecting a Device to COM1 Using RS-
485 (4-wire) ...................................................... 40
2-27. Connecting a Device to COM1 Using RS-
485 (2-wire) ...................................................... 41
2-28. Connecting a Device to COM2 or COM3
Using RS-232 ................................................... 42
2-29. Connecting a Device to COM2 or COM3
Using RS-485 (2-wire) ..................................... 43
2-30. Wiring for 2-, 3-, and 4-Wire RTD ............ 44
2-31. Wiring for DO ............................................ 45
3-1. Waking the Display ..................................... 51
3-2. Infrared (IR) Button Location ..................... 51
4-1. FB1100 Flow Computer Components ....... 54
4-2. LED Locations ............................................. 55
4-3. Captive Fastening Screws .......................... 58
4-4. Main Battery Pack ....................................... 59
4-5. Removing the Battery Pack ........................ 60
4-6. Removing/Replacing the Coin Cell Battery
.......................................................................... 62
4-7. Firmware Update Dialog ............................ 63
Firmware
upgrading ............................................................ 62
FLASH memory
amount of .............................................................. 4
G
Grounding ............................................................... 27
H
Hazardous locations .............................................. 13
HMI module .............................................................. 8
communicating using ........................................ 50
replacing .............................................................. 57
Housing
rotating ................................................................ 25
I
I/O
digital output ...................................................... 45
options ................................................................... 6
Indirect mounting .................................................. 23
Installation .............................................................. 13