Emerson FB2100 - Page 122

FB2100 Flow Computer Instruction Manual
D301783X012
November 2023
108 Index
2-1. Dimensions – Multivariable Sensor Version
- Fiberglass Enclosure .................................... 16
2-2. Dimensions – Multivariable Sensor Version
Aluminum Enclosure ...................................... 17
2-3. Dimensions – No Integral Sensor Version –
Fiberglass Enclosure ....................................... 18
2-4. Dimensions – No Integral Sensor Version –
Aluminum Enclosure ...................................... 19
2-5. Dimensions – Static Pressure Sensor
Version – Fiberglass Enclosure ...................... 20
2-6. Dimensions – Static Pressure Sensor
Version – Aluminum Enclosure ..................... 21
2-7. Grounding Stud ........................................... 22
2-8. Fiberglass Enclosure Fasteners ................. 23
2-9. Aluminum Enclosure Clamps..................... 24
2-10. Transmitter with Coplanar Flange .......... 24
2-11. Transmitter with Coplanar Flange and
Optional Flange Adapters .............................. 25
2-12. Transmitter with Traditional Flange and
Optional Flange Adapters .............................. 25
2-13. Proper Bolt Installation ............................ 26
2-14. O-rings with Flange Adapters .................. 26
2-15. Aluminum Enclosure Pole Mounting ...... 27
2-16. Fiberglass Enclosure Pole Mounting ...... 28
2-17. Aluminum Enclosure Panel or Wall
Mounting ......................................................... 29
2-18. Attaching mounting tabs ......................... 30
2-19. Fiberglass Enclosure Panel or Wall
Mounting ......................................................... 31
2-20. Housing Rotation Set Screw (1 ea. side) . 32
2-21. Conduit Entry Points – Fiberglass
Enclosure ......................................................... 33
2-22. Conduit Entry Points – Aluminum
Enclosure ......................................................... 34
2-23. Module Power Control ............................. 37
2-24. DC Power Connections ............................. 38
2-25. Removing Plastic Tabs from Batt. Pack .. 39
2-26. Captive Fastening Screws ........................ 40
2-27. Rotate Assembly Forward ........................ 41
2-28. Connect the Battery .................................. 42
2-29. Removing Termination Cover of Internal
Solar Regulator ............................................... 43
2-30. Battery Strap ............................................. 43
2-31. Easing Battery Pack into Compartment . 44
2-32. Battery Pack Attached to Compartment 44
2-33. Battery Pack Attached to Compartment 45
2-35. Battery pack attached to compartment . 48
2-36. Removing Fork Connectors ..................... 49
2-37. Wiring Solar Power ................................... 49
2-38. Wiring Solar Power ................................... 50
2-39. Routing Battery Wires .............................. 50
2-40. Wiring Solar Power ................................... 51
2-41. Wiring Solar Power-Internal .................... 52
2-42. Installing 30W Solar Panel ....................... 54
2-43. 30W Solar Panel Installed ........................ 55
2-44. Adjust. the 30W Solar Panel Tilt Angle ... 56
2-45. Adjust. the 30W Solar Panel Tilt Angle ... 57
2-46. Connecting a Device to COM1 Using RS-
232 .................................................................... 58
2-47. Connecting a Device to COM1 Using RS-
485 (4-wire) ...................................................... 59
2-48. Connecting a Device to COM1 Using RS-
485 (2-wire) ...................................................... 60
2-49. Connecting a Device to COM2 or COM3
Using RS-232 ................................................... 61
2-50. Connecting a Device to COM2 or COM3
Using RS-485 (2-wire) ..................................... 62
2-51. Wiring the Door Contact Terminal .......... 63
2-52. Board Info Screen in FBxConnect ........... 63
3-1. Base I/O – Option 2 ..................................... 66
3-2. Analog Input (AI) Wiring – (Available on IO
Option 2 ........................................................... 68
3-3. Analog Output (AO) Wiring – (IO Opt. 2) .. 69
3-4. Digital Input (DI) Wiring – (IO Option 2) ... 70
3-5. Digital Output (DO) Wiring – (IO Opt. 1) ... 72
3-6. Digital Output (DO) Wiring – (IO Opt. 2) ... 72
3-7. Pulse Input (PI) Wiring - (IO Option 2) ...... 74
3-8. Wiring for 2-Wire ......................................... 75
3-9. Wiring for 3-Wire ......................................... 75
3-10. Wiring for 4-Wire ....................................... 76
3-11. Relay Wired to Isolated DO ...................... 76