Emerson Micro Motion Configuration And Use Manual

4.6.4 Using equations to calculate specific gravity, °Baumé, °Brix, °Plato, and °Twaddell ......59
4.6.5 Matrix switching ......................................................................................................... 60
4.6.6 Measuring Net Mass Flow Rate and Net Volume Flow Rate ..........................................62
4.7 Set up flow rate measurement ...................................................................................................62
4.7.1 Set up flow rate measurement using ProLink III ...........................................................62
4.7.2 Set up flow rate measurement using the Field Communicator .................................... 64
Chapter 5 Configure device options and preferences ....................................................................67
5.1 Configure the transmitter display .............................................................................................. 67
5.1.1 Configure the language used for the display ............................................................... 67
5.1.2 Configure the process variables and diagnostic variables shown on the display ...........68
5.1.3 Configure the number of decimal places (precision) shown on the display ..................68
5.1.4 Configure the refresh rate of data shown on the display ..............................................69
5.1.5 Enable or disable automatic scrolling through the display variables ............................ 69
5.2 Enable or disable operator actions from the display ...................................................................70
5.2.1 Enable or disable the Acknowledge All Alerts display command ....................................... 70
5.3 Configure security for the display menus .................................................................................. 71
5.4 Configure alert handling ............................................................................................................72
5.4.1 Configure Fault Timeout .................................................................................................72
5.4.2 Configure Status Alert Severity ........................................................................................73
5.5 Configure informational parameters ......................................................................................... 75
Chapter 6 Integrate the meter with the control system ................................................................77
6.1 Configure Channel B ..................................................................................................................77
6.2 Configure the mA output .......................................................................................................... 78
6.2.1 Configure mA Output Process Variable ............................................................................. 78
6.2.2 Configure Lower Range Value (LRV) and Upper Range Value (URV) ....................................80
6.2.3 Configure Added Damping ............................................................................................. 81
6.2.4 Configure mA Output Fault Action and mA Output Fault Level ...............................................82
6.3 Configure the discrete output ................................................................................................... 84
6.3.1 Configure Discrete Output Source ....................................................................................84
6.3.2 Configure Discrete Output Polarity ................................................................................... 85
6.3.3 Configure Discrete Output Fault Action ............................................................................. 86
6.4 Configure an enhanced event ....................................................................................................87
6.5 Configure HART/Bell 202 communications ................................................................................88
6.5.1 Configure basic HART parameters ...............................................................................88
6.5.2 Configure HART variables (PV, SV, TV, QV) ..................................................................89
6.5.3 Configure burst communications ............................................................................... 91
6.6 Configure Modbus communications ..........................................................................................95
6.7 Configure Digital Communications Fault Action ................................................................................. 96
6.7.1 Options for Digital Communications Fault Action .................................................................97
Chapter 7 Completing the configuration ......................................................................................99
7.1 Test or tune the system using sensor simulation ........................................................................99
7.2 Back up transmitter configuration ............................................................................................. 99
7.3 Enable HART security ...............................................................................................................100
Part III Operations, maintenance, and troubleshooting
Chapter 8 Transmitter operation ................................................................................................105
8.1 Record the process variables ................................................................................................... 105
8.2 View process variables .............................................................................................................105
Contents
ii Micro Motion
®
Fork Density Meters (FDM)

Emerson Micro Motion Specifications

General

Category	Measuring Instruments
Manufacturer	Emerson
Brand	Micro Motion
Type	Coriolis Flow Meter
Output	4-20 mA, HART, Foundation Fieldbus, Profibus, Modbus
Power Supply	24 V DC
Material	Stainless Steel, Hastelloy
Process Connection	Flanged, Threaded
Certifications	ATEX, IECEx, CSA, SIL
Pressure Rating	Varies by model; up to 10, 000 psi (690 bar)
Temperature Range	Varies by model; -400 to 750°F (-240 to 400°C)