Epiroc COP M6 - Page 20

20
1
7 8
9
10 11 12 1213 14 15 16 17 18 19
2 23 4 5 6
Ref. Part Prod. No. Product code
1 Chuck 89012543 9707-CM-00-000-03-000-001
2
O-ring* for bit retaining ring &
bushing
- -
3 Bit retaining ring assembly 89012544 9707-CM-00-000-03-000-A02
4 Bit bearing assembly 89012545 9707-CM-00-000-03-000-A22
5 Casing 89012546 9707-CM-00-000-00-000-004
6 Piston 89012547 9707-CM-00-000-03-000-005
7 Stop ring 89012549 9707-CM-00-000-00-000-058
8 O-ring* for cover - -
9 O-ring* for cover - -
10 Cover 89012550 9707-CM-HF-000-00-000-021
11 Compression cone 89012551 9707-CM-00-000-00-000-014
12 Buffer 89012555 9707-CM-00-000-00-000-011
13 Control tube, HF 89012548 9707-CM-HF-000-00-000-007
13 Control tube, LF 89012624 9707-CM-LF-000-00-000-007
14 Valve body 89012556 9707-CM-00-000-00-000-015
15 Check valve spring 89001265 9705-CG-00-000-00-000-016
16 Check valve assembly 89012609 9707-CM-00-000-00-000-A17
17 Check valve seat* - -
18 O-ring* for backhead - -
19 Backhead assy 4" Beco Pin 89012639 9707-CM-00-B2P-00-0B0-A20
19 Backhead assy 4-1/2" API Pin 89012553 9704-CM-00-17P-00-0B0-A20
19 Backhead assy 4-1/2" Beco Pin 89012557 9707-CM-00-17P-00-0B0-A20
Hammers and kits Prod. No. Product code
COP M7 complete, 4 1/2" API Pin 89012558
9707-CM-HF-17P-03-0B0
COP M7 complete 4 1/2" API Pin 89012625 9707-CM-LF-17P-03-0B0
COP M7 complete 4" Beco Pin 89012640 9707-CM-HF-B2P-03-0B0
COP M7 complete 4" Beco Pin 89012641 9707-CM-LF-B2P-03-0B0
COP M7 complete, 4 1/2" Beco Pin 89012559 9707-CM-HF-B3P-03-0B0
COP M7 complete 4 1/2" Beco Pin 89012643 9707-CM-LF-B3P-03-0B0
Economy kit 4" Beco Pin
incl. 1, 5, 15, 19 and O-ring kit
89012642 9707-CM-00-B2P-03-0B0-K40
Economy kit 4-1/2" API Pin
incl. item 1, 5, 15, 19 and O-ring kit
89012561 9707-CM-00-17P-03-0B0-K40
Economy kit 4-1/2" Beco Pin
incl. item 1, 5, 15, 19 and O-ring kit
89012560 9707-CM-00-B3P-03-0B0-K40
O-ring kit incl. item 2, 8, 9, 12, 17, 18 89012562
9707-CM-000-000-00-000-K47
Wear limits
Casing, lower end Min. OD 165 mm.
Piston/casing clearance Max. 0,3 mm.
Piston/control tube Max. 0,3 mm.
Piston/bit bushing Max. 0,4 mm.
* O-rings not sold seperately. Included in dierent kits – see table.
Secoroc COP M7
Down-the-hole hammer