Need help?Do you have a question about the ETC ArcSystem Navis 100 and is the answer not in the manual?
Explains document conventions like Note, Caution, and Warning statements.
Warns about potentially hazardous optical radiation from the luminaire and advises not to stare at the lamp.
Informs that the light source is not replaceable and the entire luminaire must be replaced at end-of-life.
Lists critical safety precautions to be followed when using electrical equipment.
Emphasizes the need for an accessible input power disconnect device before installation.
Details environmental, physical, and spacing requirements for installing the luminaire.
Provides guidance on using RJ45 connectors and cable types for luminaire wiring.
Warns that luminaires are NON-IC rated and not suitable for direct contact with combustible materials or insulation.
Advises installing the luminaire at least 0.1m (4.0 in) away from all lighted objects.
Cautions that RGBW luminaires should be positioned to avoid prolonged staring from a distance.
Lists required tools and specifies torque settings for luminaire installation screws.
Details the procedure for installing a luminaire, including trim plate, optics, and channel settings.
Details preparing RGBW wall wash luminaires with spacer pads and angle templates.
Outlines the steps for installing a wall wash luminaire, including template use and trim plate attachment.
Explains how to use the RDM command to identify connected luminaires.
Refers to the F-Drive W1 Driver Installation Manual for emergency system testing.
Refers to the F-Drive series driver manual for updating RGBW luminaire firmware.
States that Navis 100 luminaires are not serviceable and to contact ETC for issues.
Lists tools and outlines the steps for removing the old lens and installing a new one.
Lists tools and outlines the steps for removing the old secondary optic and installing a new one.
Provides critical warnings and cautions regarding disconnecting power and cleaning the luminaire.
Details the approved methods for cleaning the luminaire using compressed air or a soft cloth.
Explains the FCC Part 15 Class A compliance and operational conditions for the device.
Explains document conventions like Note, Caution, and Warning statements.
Warns about potentially hazardous optical radiation from the luminaire and advises not to stare at the lamp.
Informs that the light source is not replaceable and the entire luminaire must be replaced at end-of-life.
Lists critical safety precautions to be followed when using electrical equipment.
Emphasizes the need for an accessible input power disconnect device before installation.
Details environmental, physical, and spacing requirements for installing the luminaire.
Provides guidance on using RJ45 connectors and cable types for luminaire wiring.
Warns that luminaires are NON-IC rated and not suitable for direct contact with combustible materials or insulation.
Advises installing the luminaire at least 0.1m (4.0 in) away from all lighted objects.
Cautions that RGBW luminaires should be positioned to avoid prolonged staring from a distance.
Lists required tools and specifies torque settings for luminaire installation screws.
Details the procedure for installing a luminaire, including trim plate, optics, and channel settings.
Details preparing RGBW wall wash luminaires with spacer pads and angle templates.
Outlines the steps for installing a wall wash luminaire, including template use and trim plate attachment.
Explains how to use the RDM command to identify connected luminaires.
Refers to the F-Drive W1 Driver Installation Manual for emergency system testing.
Refers to the F-Drive series driver manual for updating RGBW luminaire firmware.
States that Navis 100 luminaires are not serviceable and to contact ETC for issues.
Lists tools and outlines the steps for removing the old lens and installing a new one.
Lists tools and outlines the steps for removing the old secondary optic and installing a new one.
Provides critical warnings and cautions regarding disconnecting power and cleaning the luminaire.
Details the approved methods for cleaning the luminaire using compressed air or a soft cloth.
Explains the FCC Part 15 Class A compliance and operational conditions for the device.
General| Light Engine Wattage | 100W |
|---|---|
| Wattage | 100W |
| Color Temperature | 2700K, 3000K, 3500K, 4000K, 5000K |
| Control Protocol | DMX/RDM |
| Type | LED |
| LED Source | LED |
| CRI | 90+ |
| Beam Angle | 15°, 25° |
| Housing | Cast aluminum |
To Next Page