Extron electronics DTP CrossPoint 108 4K - Page 76

Command and Response Table for Matrix Switcher Commands (continued)
DTP CrossPoint 4K Series Matrix Switchers • Programming Guide 68
Command Function
SIS Command
(Host to Unit)
Response
(Unit to Host)
Additional description
Logo Commands
Logo on and off
Assign a logo to an output
E
E
X2!
*
X4!
LOGO
}
LogoE
X2!
*
X4!]
Assign logo
X4!
to output
X2!
.
Example:
E
E6*4LOGO
}
LogoE6*4
]
Assign logo 4 to output 6.
Unassign a logo
E
E
X2!
*0LOGO
}
LogoE
X2!
*0
]
Set output
X2!
to output no logo.
View logo assignment
E
E
X2!
LOGO
} X4!]
Logo
X4!
is assigned to output
X2!
.
View all logo assignments
E
ELogo
}
Each
X4!
is the logo status of a scaler
output, starting from output 5.
X4!
s in
response to this command are all 2-digit.
00•00•00•00•
X4!
•
X4!
•
X4!
•
X4!]
RS-232 Insertion Commands
Captive screw and Ethernet serial port insertion enables
Enable an input captive screw serial
port insertion
E
I
X1(
*0LRPT
}
LrptI
X1(
*0
]
Enable the captive screw serial port
insert on input
X1(
. This disables the
Ethernet RS-232 insert.
Enable an input Ethernet serial port
insertion
E
I
X1(
*1LRPT
}
LrptI
X1(
*1
]
Enable the Ethernet serial port insert
on input
X1(
. This disables the captive
screw serial port insert.
Set all RS-232 input insertions
E
I
X4@
*LRPT
}
LrptI
X4@]
View input insertion
E
I
X1(
LRPT
} X4@]
View all input insertions
E
ILRPT
} X4@
7
X4@
8
X4@
9
X4@
10
]
One
X4@
for each available input, starting
at input 7.
Enable an output captive screw
serial port insertion
E
O
X2!
*0LRPT
}
LrptO
X2!
*0
]
Enable the captive screw serial port
insert on output
X2!
. This disables the
Ethernet serial port insert.
Enable an output Ethernet serial port
insertion
E
O
X2!
*1LRPT
}
LrptO
X2!
*1
]
Enable the Ethernet serial port insert
on output
X2!
. This disables the
captive screw serial port insert.
Set all RS-232 output insertions
E
O
X4@
*LRPT
}
LrptO
X4@]
View RS-232 output insertion
E
O
X2!
LRPT
} X4@]
View all output insertions
E
OLRPT
} X4@
5
X4@
6
X4@
7
X4@
8
]
One
X4@
for each available output,
starting at output 5.
NOTE: X1( = TP and insertion input number 07 – 10
X2! = TP (scaled) and insertion output number 05 – 08
X4! = Logo number 00 – 16 ( 00 = no logo)
X4@ = Captive screw or UART 0 = Captive screw RS-232 insert (default) 1 = Ethernet RS-232 insert (UART)