Fayat Group Dynapac SD2500C - Page 158

Fayat Group Dynapac SD2500C

588 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

D 11 64

122

124

125

123

125

122

124

Table of Contents

Table of contents3
V Preface15
- 1 General safety instructions16
- 2 CE identification and Declaration of Conformity24
- 3 Guarantee conditions24
- 4 Residual risks25
- 5 Sensibly predictable incorrect usage26
A Correct use and application27
B Vehicle description29
- 1 Application29
- 2 Description of assemblies and functions30
  - 2.1 Vehicle31
    - Construction31
- 3 Danger zones36
- 4 Safety devices37
- 5 Technical data, standard configuration39
- 6 Location of instruction labels and identification plates49
- 7 EN standards65
C 11 Transportation69
- 1 Safety regulations for transportation69
- 2 Transportation on low-bed trailers70
  - 2.1 Preparations70
- 3 Securing the load72
- 4 Securing the load77
- 5 Control panel transport safeguard:80
  - 5.1 After transportation81
    - Protective roof (o)82
- 6 Transportation84
  - 6.1 Preparations84
  - 6.2 Driving mode86
- 7 Loading by crane87
- 8 Towing90
- 9 Safely parking the vehicle93
  - 9.1 Lifting the vehicle with hydraulic lifts, lifting points94
D 11 Operation95
- 1 Safety regulations95
- 2 Controls97
  - 2.1 Operating panel97
- 3 Remote control154
D 22 Operating the display173
- 1 Operation of the input and display terminal174
  - Button layout on the display174
  - 1.1 Menu operation - procedure for adjusting parameters176
    - Selecting and changing an adjustment parameter in a menu178
    - Selecting and changing a selection possibility in a menu179
- 2 Menu structure180
- 2 Terminal error messages214
- 3 Menu structure of the setting and display menus264
D 30 Operation265
- 1 Operating elements on the paver finisher265
  - 1.1 Control elements on the operator's control station265
D 41 Mode of operation309
- 1 Preparing for operation309
- 2 Malfunctions346
  - 2.1 Problems during paving346
  - 2.2 Malfunctions on the paver finisher or screed348
E 10 Set-up and modification351
- 1 Special notes on safety351
- 2 Distribution auger352
- 3 Auger extension356
- 4 Offsetting the screed375
- 5 Levelling376
- 6 Automatic steering unit391
  - 6.1 Mounting the automatic steering unit on the paver finisher392
- 7 Emergency stop during feeder operation395
- 8 Limit switch396
  - 8.1 Auger limit switches (left and right) - mounting the PLC version396
  - 8.2 Auger limit switches (left and right) - mounting the conventional version397
- 9 Special accessories398
  - 9.1 Material bucket398
- 10 Identification points403
- 11 Screed418
- 12 Electrical connections418
  - 12.1 Machine operation without remote control / side board419
F 10 Maintenance421
- 1 Notes regarding safety421
F 25 Maintenance review423
- 1 Maintenance review423
F 31 Maintenance - conveyor425
- 1 Maintenance - conveyor425
  - 1.1 Maintenance intervals427
  - 1.2 Points of maintenance428
F 40 Maintenance - auger assembly433
- 1 Maintenance - auger assembly433
  - 1.1 Maintenance intervals435
  - 1.2 Points of maintenance437
F 50 Maintenance - engine assembly Tier 3 (o)445
- 1 Maintenance - engine assembly445
  - 1.1 Maintenance intervals447
  - 1.2 Points of maintenance450
F 52 Maintenance - engine assembly Tier 4i (o)461
- 1 Maintenance - engine assembly461
  - 1.1 Maintenance intervals463
  - 1.2 Points of maintenance466
F 54 Maintenance - engine assembly Tier 4F (o)479
- 1 Maintenance - engine assembly479
  - 1.1 Maintenance intervals481
  - 1.2 Points of maintenance485
F 60 Maintenance - hydraulic system515
- 1 Maintenance - hydraulic system515
  - 1.1 Maintenance intervals517
  - 1.2 Points of maintenance519
F 73 Maintenance – drive units531
- 1 Maintenance – drive units531
  - 1.1 Maintenance intervals533
  - 1.2 Points of maintenance536
F 81 Maintenance - electrical system545
- 1 Maintenance - electrical system545
  - 1.1 Maintenance intervals547
  - 1.2 Points of maintenance548
F 90 Maintenance - lubricating points559
- 1 Maintenance - lubricating points559
  - 1.1 Maintenance intervals560
  - 1.2 Points of maintenance561
    - Central lubrication system (1)561
    - Bearing points (2)565
F 100 Tests, stopping ...567
- 1 Tests, checks, cleaning, stopping567
  - 1.1 Maintenance intervals568
- 2 General visual inspection569
- 3 Check that the bolts and nuts fit firmly569
- 4 Inspection by an expert570
- 5 Cleaning571
- 6 Preserving the paver finisher574
- 7 Environmental protection, disposal576
  - 7.1 Environmental protection576
  - 7.2 Disposal576
- 8 Bolts - torques577
  - 8.1 Standard metric threads - strength class 8.8 / 10.9 / 12.9577
  - 8.2 Fine metric threads - strength class 8.8 / 10.9 / 12.9578
F 114 Lubricants and operating substances579
- 1 Lubricants and operating substances579
  - 1.1 Capacities581
- 2 Operating substance specifications582

Related product manuals

Preview: Fayat Group Dynapac CA25

Fayat Group Dynapac CA25

Preview: Fayat Group Dynapac CC800

Fayat Group Dynapac CC800

Preview: Fayat Group Dynapac CC900G

Fayat Group Dynapac CC900G

Preview: Fayat Group DYNAPAC CA5000

Fayat Group DYNAPAC CA5000

Fayat Group DYNAPAC CA6000

Preview: Fayat Group DYNAPAC CA4600

Fayat Group DYNAPAC CA4600

Preview: Fayat Group DYNAPAC CC224HF

Fayat Group DYNAPAC CC224HF

Preview: Fayat Group BOMAG BW 213 D-5

Fayat Group BOMAG BW 213 D-5

Preview: Fayat Group BOMAG BW 226 DH-4

Fayat Group BOMAG BW 226 DH-4

Preview: BOMAG BW 213 DH-4 BVC

BOMAG BW 213 DH-4 BVC

Fayat Group BOMAG BW177PDH-50

Preview: Fayat Group BOMAG BF 700 C S600

Fayat Group BOMAG BF 700 C S600